We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
4. The earth fault current of a 20 kV overhead line is 0,065 A/km and the...
Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which is 20% of the total line 2 length from Bus B Fault MVA 1524.20471 Three-phase fault level in MVA at bus A SPFL (kA) 8 MVA1 MVA2 X1 (96 X2 (96) R1 (2) R2 (Q) z' (Q) Zo (2) Rf (Q) Single phase to ground fault level (kA) at bus A Transformer 1 MVA...
Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which is 20% of the total line 2 length from Bus B Fault MVA 1524.20471 Three-phase fault level in MVA at bus A SPFL (kA) 8 MVA1 MVA2 X1 (96 X2 (96) R1 (2) R2 (Q) z' (Q) Zo (2) Rf (Q) Single phase to ground fault level (kA) at bus A Transformer 1 MVA...
Bus A Bus B R1 T1 line 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which is 20% of the total line 2 length from Bus B Fault MVA 1524.20471 Three-phase fault level in MVA at bus A SPFL (kA) 8 MVA1 MVA2 X1 (96) X2 (96) R1 (2) R2 (Q) z' (Q) Zo (2) Rf (Q) Single phase to ground fault level (kA) at bus A Transformer 1 MVA...
Problem 2 (10 pts) 132 kV TL 40 km 1 pu mid-point L-E fault 60 ΛΤΑ TL: Transmission line. L-E fault: Line-to-earth fault. Z. 0.07 pu 0.1 pu Generator 0.1 pu 0.1 pu 0.1 pu Transformers 2.5x Z] Transmission Line 0.7 Ω/km 0.7 Ω/km Suppose a single L-E fault happens at the mid-point of the transmission line. Determine the per unit phase voltage and current at point P (Choose Sbase-60 MVA and Vbase-132 kV). (4 pts) * The phase impedance...
Please show all the steps
A 60-Hz three-phase, three-wire overhead line has solid cylindrical conductors arranged in the form of an equilateral triangle with 4 ft conductor spacing. Conductor diameter is 0.5 in a) Calculate the positive-sequence inductance in H/m and the positive-sequence inductive reactance in 2/km. b) Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line stated above. Neglect the effect of the earth plane. c) Rework b) if the phase spacing is i)...
Note: # 1 states line to line fault occurs, while # 2 states double line to ground fault occurs Please explain the solution thoroughly with diagrams The positive, negative, and zero sequence reactances of a 15-MVA, 11-kV, 3ph, wye-connected generator are 11%, 8% and 3%, respectively. The neutral of the generator is grounded, and the generator is excited to the rated voltage on open circuit. A line-to-line fault occurs between phases b and c of the generator while phase a...
A 200-km, 230-kV, 60-Hz three-phase line has a positive-sequence
series impedance ?=0.08+?0.48 Ω/km and a positive-sequence shunt
admittance ?=?3.33×10−6 S/km. At full load, the line delivers 250
MW at 0.99 pf lagging and at 220 kV. Using the nominal ? circuit,
calculate:
a. The ABCD parameters,
b. The sending-end voltage and current,
c. The percent voltage regulation.
Bus A Bus B R1 T1 line 1 20% 80% line 2 T2 R2 110 kV 11 kV Note TX impedance TX leakage reactance TX zero sequence impedance-TX positive Data 3 phase fault MVA Bus A 1152 MVA Single P-G level Bus A 8k T1 = T2 = 50MVA X1 0.006 RAk TX1 X2 0.0055 Rik TX2 Earthing resistance-R1-R2-2 ohm z+ sequence reactance 55j) ohm for both sequence impedance Source negative impedance -positive sequence impedance Source zero sequence impedance- purely...
I need help in matlab codes please
Single line to ground fault analysis Example 9.4 Problem 1 A three-phase, il kV, 30 MVA alternator with grounded neutral has a direct axis subtransien pu respectively based on system base. A single line to ground fault has occurred in phase a. Determine the fault current, line to ground voltages in pu. t, negative sequence and zero sequence reactances of 0.2 pu, 0.3 pu and 0.1 Solution: Phase voltage E.0 pu From equation...
The following are the answers:
Autumn 2013 T1 G1 5 kV 50 MVA 5/20 kV 50 MVA 20 kV 50 MVA X 0.1 p.u Figure A13 In the system shown, per-unit series equivalent impedances are shown for each element. Before a balanced 3-phase fault occurs in the location shown, the pre-fault current is at its rated value at 90 % lagging power factor flowing from generator G1 The generator is operating at full voltage. How much current in kA is...