for the following circuit with zero initial voltage Vacol=0 to R6 RO lor 512 V2 D(=30V...

Question

Question

for the following circuit with zero initial voltage Vacol=0 to R6 RO lor 512 V2 D(=30V 3R7 R9 G to 102 52 cl o, 1 л find an O

Answer 1

Answer #1

Given that Ve X A lon 5n t=0 silpnoth Bov Ver + v Elon @ Oluf Solution: Stepi) Assign the node voltages V1, V₂ and Ves as sho

T 1:2X106 veya By ict at Kce 따alocle : [V - Ves C, dva, at By salving: V2 = (su dva + VCD from equation til and (i) : 2K - X

Stepliii) Now V = ? After reaching steady State (y will be have open circuit. Hence final circuidar as lor v + sr se lon 1 5~

Feel Free to ask in comment section, if there is any doubt.

Answer 2

Similar Homework Help Questions

8.23 The initial value of the voltage v in the circuit in Fig. 8.1 is zero,...

8.23 The initial value of the voltage v in the circuit in Fig. 8.1 is zero, and the initial value of the capacitor current, ic(0*), is 45 mA. The expression for the capacitor current is known to be i(t) = Aje-200t + Aze-8001, 1 2 0+, when R is 250 N. Find a) the values of a, wo, L, C, A1, and A2 Hint: u:... dic(0*) _ 1. dt di_(0+) dt dir(ot) dt -v(0) L 1 ic(0+) R C ....
- 0 L-100mH For the circuit shown, if the initial current in the inductor was zero,...

- 0 L-100mH For the circuit shown, if the initial current in the inductor was zero, and the transient response of VR is as shown in the given curve, find R. CL + VL- V =?? ► VR (1) 2m 3m Time (s)
Problem 1 Given the circuit shown below in Fig. 1.1: Write the ordinary differential equation (ODE)...

Problem 1 Given the circuit shown below in Fig. 1.1: Write the ordinary differential equation (ODE) for the capacitor voltage. Find the zero-state unit step responses of v(t) and i(t) if vs-u(t) V using each of the following three methods of solving the ODE: a. b. i. ii. Solve the ODE by integrating for the solution; Solve the ODE by assuming homogeneous and particular solutions; Solve the ODE by using the general form solution for a 1st order ODE. iii....

Determine the total Resistance and voltage a point A, B, and C in the circuit, 200...

Determine the total Resistance and voltage a point A, B, and C in the circuit, 200 52 200 A 8 30V 7002 300. I K 20.01 Paka izka it 5 4 o- . ; 7 5 6 O U P I E Y 1 T R T L K S D F G H V M х Z B CV X command option end
- Calculate the magnitude of the voltage V2 in the following circuit E-21 V 12 a-...

- Calculate the magnitude of the voltage V2 in the following circuit E-21 V 12 a- 14V b. -14 V C. 28 V 7- A sinusoidal signal has a period of 40 ms. What is its frequency? a. 50k㎐b, 25 kHz C.50 ㎐ ④25㎐ 8- The voltage across a component is measured as 80 V r.m.s. and current through it is 4 A r.m.s. If the current leads the voltage by 2 what is the apparent power in the component?...
4. The MOSFET in the circuit given below has Vi- 1 V, kn 0.8 mA/V2, and VA 40 V a) Find the values of Rs, Ro, and Ro so that Io -0.1 mA, the largest possible value for RD is used while a maximum...

4. The MOSFET in the circuit given below has Vi- 1 V, kn 0.8 mA/V2, and VA 40 V a) Find the values of Rs, Ro, and Ro so that Io -0.1 mA, the largest possible value for RD is used while a maximum signal swing at the drain of tl V is possible, and the input resistance at the gate is 10 MS2. b) Find the values of gm and ro at the bias point c) If terminal Z...

9. For the given circuit, if the initial voltage across the capacitor is vc(0*) = 0,...

9. For the given circuit, if the initial voltage across the capacitor is vc(0*) = 0, find an expression for the voltrage across the capacitor as a function of time and graph voltage versus time. R= 100 k2 w v=100 V uc) C = 0.01 uF 10. If a 100-F capacitance is initially charged to 1000V and at t=0, it is connected to a 1-ka resistance, at what time has 50 percent of the initial energy stored in the capacitance...
An interconnect circuit is being considered as part of a new logic architecture R1 R3 R4 R6 R7 R9...

An interconnect circuit is being considered as part of a new logic architecture R1 R3 R4 R6 R7 R9 R10 C3 C4 C6 C7 C9 C10 R2 R5 R8 V(t) C1 C2 C5 C8 Initially, assume unit circuit elements. That is, the capacitors C1,..,C10 F, the resistors R.,..Rio-12m and voltage, V(t)-1 V. At t-0, the switch is closed. The voltages across the capacitors (C[i], here Cl to C10) are represented as x, Hint: V(t) may be seen as an input/control...
2) In the following circuit, V- 10et V. If V,(0)- 2V, find: a) V2(0), 20uF b)...

2) In the following circuit, V- 10et V. If V,(0)- 2V, find: a) V2(0), 20uF b) V4(t), c) V2(t), o f) /12(t), 30HF

30. Consider the circuit shown in Figure P17.30, having zero initial stored energy. Let (a) Find ...

30. Consider the circuit shown in Figure P17.30, having zero initial stored energy. Let (a) Find Z6 (b) Find Z) io Find Ga-Vi (d) Find Gv2 =K (e Find G (f Find the response, v2), to the input in +0,1H 02H る(x ylo 2200 1 H. Figure P17.30 30. Consider the circuit shown in Figure P17.30, having zero initial stored energy. Let (a) Find Z6 (b) Find Z) io Find Ga-Vi (d) Find Gv2 =K (e Find G (f Find...