Homework Answers
Add Answer to:
The temperature distribution across a wall 1 m thick at a certain instant of time is...
The temperature distribution across a wall 0.2 m thick at a certain instant of time is...
The temperature distribution across a wall 0.2 m thick at a certain instant of time is T(x) = a + bx + cxº, where T is in degrees Celsius and x is in meters, a = 200°C, b = -190°c/m, and c = 30°C/m2. The wall has a thermal conductivity of 1 W/m.k. (a) On a unit surface area basis, determine the rate of heat transfer into and out of the wall and the rate of change of energy stored...
The steady state temperature distribution across a wall, where -0.02 m, is T(X)*+bx+ A uniform heat...
The steady state temperature distribution across a wall, where -0.02 m, is T(X)*+bx+ A uniform heat generation rate. 9. ration rate. 9. Occurs in the wall and is given in the table below. Coefficients a, b and care in units shown in the table and x is in meters. The origin of the x coordinate is at the middle of the wall as shown. Each side of the wall experiences convection from a fluid at -20°C 82 K (thermal conductivity...
Problem 3. A plane wall of thickness 2L = 40 mm and thermal conductivity k =...
Problem 3. A plane wall of thickness 2L = 40 mm and thermal conductivity k = 5 W/m.K experiences uniform volumetric heat generation at a rate ġ, while convection heat transfer occurs at both of its surfaces (x = -1, + L), each of which is exposed to a fluid of temperature Too = 20 °C. Under steady-state conditions, the temperature distribution in the wall is of the form T(x) = a + bx + cx? where a = 82.0°C,...
A 0.1 m thick brick wall with thermal conductivity 0.66 Wm K-1 is exposed to cold wind on the out...
A 0.1 m thick brick wall with thermal conductivity 0.66 Wm K-1 is exposed to cold wind on the outside of a house, at 270 K with convective heat transfer coefficient of 22.43 Wm2K1. On the inside of the house is calm air at 295.8 K, with a natural convective heat transfer coefficient of 10.49 Calculate the rate of heat transfer per unit area, in Wm, giving your answer to 3 decimal places
A 0.1 m thick brick wall with...
3. The wall shown in the figure below has thickness L 0.25 m and uniform thermal...
3. The wall shown in the figure below has thickness L 0.25 m and uniform thermal conductivity k-1 W/mK. It is exposed to circulating fluid on the surface at x = L, where the temperature ofthe fluid is T-= 30°C and the convection coefficient is h = 4 W/m2.K. The surface at x = 0 is maintained at constant temperature T-20 °C. Assume ID heat flux, and that the system is at steady state a) b) Determine the temperature distribution...
A large wall made of 10-cm-thick solid brick (k = 0.8 W/m.K, p 2000 kg/m3, and p 800 J/kg.K) is o...
Heat transfer question.
A large wall made of 10-cm-thick solid brick (k = 0.8 W/m.K, p 2000 kg/m3, and p 800 J/kg.K) is originally at a uniform temperature of 30°C. The wall is adiabatic (well insulated) on one side as shown in the figure. The other surface is suddenly exposed to convection air flow at 10°C, resulting in a heat transfer coefficient h=40W/m2.K. Fluid (4.1) Determine the temperature of both surfaces Gr 0 and x 10 cm) after 5 hr...
Consider a 4 m high, 6 m wide and 0.17 m thick wall whose thermal conductivity is k = 0.8 W/m.oC....
Consider a 4 m high, 6 m wide and 0.17 m thick wall whose thermal conductivity is k = 0.8 W/m.oC. On a certain day, the temperatures of the inner and the outer medium close to the wall are measured to be 14oC and 6oC, respectively. Both inner and outer surfaces are subjected to convection heat transfer. Assume that the convection heat transfer coefficient is the same for the two surfaces h = 5 W/m2 ∙ °C. 1. Draw the...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The wall is 20 cm thick and has a surface area of 10 m2. One side of the wall is exposed to outside air blowing against the wall resulting in a heat transfer coefficient of 20 W/(m2-K). The other side is exposed to an air-conditioned room with a convective heat transfer coefficient of 5 W/(m2-K). a. What are the thermal resistances corresponding to conduction through...
The upper surface of a 60-cm-thick solid plate (k = 237 W/m.K) is being cooled by...
The upper surface of a 60-cm-thick solid plate (k = 237 W/m.K) is being cooled by water with temperature of 20°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 120°C, respectively. Given: The thermal conductivity of the solid plate is given as k= 237 W/m.K. (T1+T) The thermal conductivity of water at the film temperature of Tf =(60°C + 20°C)/2 = 40°C is kfluid = 0.631 W/m.K. = 2 1. value: 3.00...
A plane wall of thickness 2L= 30 mm and thermal conductivity k= 3 W/m·K experiences uniform...
A plane wall of thickness 2L= 30 mm and thermal conductivity k= 3 W/m·K experiences uniform volumetric heat generation at a rate q˙, while convection heat transfer occurs at both of its surfaces (x=-L, +L), each of which is exposed to a fluid of temperature ∞T∞= 20°C. Under steady-state conditions, the temperature distribution in the wall is of the form T(x)=a+bx+cx2 where a= 82.0°C, b= -210°C/m, c= -2 × 104°C/m2, and x is in meters. The origin of the x-coordinate...
The temperature distribution across a wall 0.2 m thick at a certain instant of time is T(x) = a + bx + cxº, where T is in degrees Celsius and x is in meters, a = 200°C, b = -190°c/m, and c = 30°C/m2. The wall has a thermal conductivity of 1 W/m.k. (a) On a unit surface area basis, determine the rate of heat transfer into and out of the wall and the rate of change of energy stored...
The steady state temperature distribution across a wall, where -0.02 m, is T(X)*+bx+ A uniform heat generation rate. 9. ration rate. 9. Occurs in the wall and is given in the table below. Coefficients a, b and care in units shown in the table and x is in meters. The origin of the x coordinate is at the middle of the wall as shown. Each side of the wall experiences convection from a fluid at -20°C 82 K (thermal conductivity...
Problem 3. A plane wall of thickness 2L = 40 mm and thermal conductivity k = 5 W/m.K experiences uniform volumetric heat generation at a rate ġ, while convection heat transfer occurs at both of its surfaces (x = -1, + L), each of which is exposed to a fluid of temperature Too = 20 °C. Under steady-state conditions, the temperature distribution in the wall is of the form T(x) = a + bx + cx? where a = 82.0°C,...
A 0.1 m thick brick wall with thermal conductivity 0.66 Wm K-1 is exposed to cold wind on the outside of a house, at 270 K with convective heat transfer coefficient of 22.43 Wm2K1. On the inside of the house is calm air at 295.8 K, with a natural convective heat transfer coefficient of 10.49 Calculate the rate of heat transfer per unit area, in Wm, giving your answer to 3 decimal places
A 0.1 m thick brick wall with...
3. The wall shown in the figure below has thickness L 0.25 m and uniform thermal conductivity k-1 W/mK. It is exposed to circulating fluid on the surface at x = L, where the temperature ofthe fluid is T-= 30°C and the convection coefficient is h = 4 W/m2.K. The surface at x = 0 is maintained at constant temperature T-20 °C. Assume ID heat flux, and that the system is at steady state a) b) Determine the temperature distribution...
Heat transfer question.
A large wall made of 10-cm-thick solid brick (k = 0.8 W/m.K, p 2000 kg/m3, and p 800 J/kg.K) is originally at a uniform temperature of 30°C. The wall is adiabatic (well insulated) on one side as shown in the figure. The other surface is suddenly exposed to convection air flow at 10°C, resulting in a heat transfer coefficient h=40W/m2.K. Fluid (4.1) Determine the temperature of both surfaces Gr 0 and x 10 cm) after 5 hr...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The wall is 20 cm thick and has a surface area of 10 m2. One side of the wall is exposed to outside air blowing against the wall resulting in a heat transfer coefficient of 20 W/(m2-K). The other side is exposed to an air-conditioned room with a convective heat transfer coefficient of 5 W/(m2-K). a. What are the thermal resistances corresponding to conduction through...
The upper surface of a 60-cm-thick solid plate (k = 237 W/m.K) is being cooled by water with temperature of 20°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 120°C, respectively. Given: The thermal conductivity of the solid plate is given as k= 237 W/m.K. (T1+T) The thermal conductivity of water at the film temperature of Tf =(60°C + 20°C)/2 = 40°C is kfluid = 0.631 W/m.K. = 2 1. value: 3.00...
Most questions answered within 3 hours.
-
Rice Products in Bangladesh
Business behavior is derived in large part from the basic cultural
environment...
asked 49 minutes ago -
The following base sequence is found for a mRNA fragment from
wild-type E. coli: 5'- UAUCAGUAGAUAAUGUAACC-3'...
asked 1 hour ago -
For this exercise, round all regression parameters to three
decimal places.
One of the two tables...
asked 1 hour ago -
What is the 5% level of significance for mean = 3.60, standard
deviation = 0.94, and...
asked 1 hour ago -
Prior to beginning work on this discussion, please read the
article by Hayley Peterson, 15 Companies...
asked 2 hours ago -
Which pair of aqueous solutions, when mixed, will form a
precipitate?
A) NaNO3 and AgC2H3O2
B)...
asked 2 hours ago -
1-Write an algorithm to get two numbers from the user (as
inputs) and calculate the sum...
asked 5 hours ago -
Define white-collar crime. What is the difference between
offender and offense-based definitions of white-collar crime? What...
asked 6 hours ago -
Consider a reaction which is 1st order with respect to A and 1st
order with respect...
asked 6 hours ago -
c++
The length of the hypotenuse of a right-angled triangle is the
square root of the...
asked 6 hours ago -
When a metal rod is heated, not only its resistance but also its
length and cross‐sectional...
asked 6 hours ago -
write a c++ program that computes the L^1 - Norm of a given
vector (L^1 norm...
asked 6 hours ago