ZuoTi.Pro
Question

a 1-in diameter steel bar is 25ft long and balanced at the middle in a horizontal...


a 1-in diameter steel bar is 25ft long and balanced at the middle in a horizontal position. calculate the distance that the ends deflect below the middle of the bar due to the weight of the bar

engineering   Civil-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

0 0
Add a comment
Know the answer?
Add Answer to:
a 1-in diameter steel bar is 25ft long and balanced at the middle in a horizontal...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • a steel bar of 25mm diameter and 122m long absorbs QUESTION 2 A steel bar of...

    a steel bar of 25mm diameter and 122m long absorbs QUESTION 2 A steel bar of 25 mm diameter and 1 22 m long absorbs 65 Nm oft energy at its lmit of proportionality under axial loading Assume the modulus of elasticty to be E 200 x 10 Pa and calculate 21 The stress induced in the bar, 22 The load when Gradually applied. Suddenly applied, Dropped through a height of 120 mm The following formula may be applied TURN...

  • A 22.0-m-long bar of steel expands due to a temperature increase. A 11.0-m-long bar of copper...

    A 22.0-m-long bar of steel expands due to a temperature increase. A 11.0-m-long bar of copper also gets longer due to the same temperature rise. The two bars were originally separated by a gap of 1.6 cm. Assume the steel and copper bars are fixed on the ends, as shown in the following figure. 1) Calculate the change in temperature if the gap is exactly "closed" by the expanding bars. (Express your answer to two significant figures.) Answer in K...

  • 1o. If a 20 inch long, 2 inch diameter stainless steel bar is to be turned down to 1 inch diamete...

    1o. If a 20 inch long, 2 inch diameter stainless steel bar is to be turned down to 1 inch diameter on a lathe, select V, f , and find N, MRR, Tm, HP, and HP assuming the efficiency of the motor to be 80%. 1o. If a 20 inch long, 2 inch diameter stainless steel bar is to be turned down to 1 inch diameter on a lathe, select V, f , and find N, MRR, Tm, HP, and...

  • In a butcher shop, a horizontal steel bar of mass 3.92 kg and length 1.40m is...

    In a butcher shop, a horizontal steel bar of mass 3.92 kg and length 1.40m is supported by two vertical wires attached to its ends. The butcher hangs a sausage of mass 2.34kg from a hook that is at a distance of 0.20m from the left end of the bar. What are the denotes the tension in the right wire.

  • 3. A steel bar having a diameter of 1 inch is being loaded as shown below....

    3. A steel bar having a diameter of 1 inch is being loaded as shown below. Assume the width and diameters of the collars are negligible. The steel's elastic modulus E = 29,000 ksi. 3000 lb 9000 lb --8000 lb - 4000 lb - 36 in. — 36 in 36 in. (a) (4 points) the maximum axial stress within the bar (also indicate it is within which section and if it's tension or compression) (6) (3 points) determine the total...

  • 1. A steel bar with solid circular cross section has a diameter d= 2.5 in., a...

    1. A steel bar with solid circular cross section has a diameter d= 2.5 in., a length L = 60 in. and a shear modulus of elasticity G = 1 1.5 × 106 psi. The bar is subjected to torque T- 350 lb-ft as shown. (a) Find the angle of twist between the d 2.5 in (b) Find the maximum shear stress in the (c) Find the shear stress ta at a distance (d) Find the shear stress Tcenter at...

  • A long steel bar (20 mm diameter) at 455°C is placed horizontally in a water bath...

    A long steel bar (20 mm diameter) at 455°C is placed horizontally in a water bath at 100°C under atmospheric pressure. (a) Estimate the initial heat transfer rate per unit length of the bar to the water when it is initially placed in water. You may assume emissivity of the steel bar to be 1. (b) What type of heat transfer mechanism is present when the bar has cooled to 110°C.

  • P.1.9. A bar of mild steel has a diameter of 75 mm and is placed inside...

    P.1.9. A bar of mild steel has a diameter of 75 mm and is placed inside a hollow aluminum cylinder of internal diameter 75 mm and external diameter 100 mm; both bar and cylinder are the same length. The resulting composite bar is subjected to an axial compressive load of 1000 KN. If the bar and cylinder contract by the same amount, calculate the stress in each. The temperature of the compressed composite bar is then reduced by 150°C but...

  • A long steel bar with a diameter of 4 cm (ρ = 7840 kg / m3...

    A long steel bar with a diameter of 4 cm (ρ = 7840 kg / m3 , cp = 580 J / kg ° K, k = 52 W / mK, α = 1.21x10-5 m2 / s), internal enters the 2 m long moving belt heat treatment furnace at ambient temperature of 900 ° C at 40 ° C. Since the film coefficient in the oven is 100 W / m2K, the center axis temperature of the bar at the...

  • 1-A 10 m long bar is attached by a frictionless hinge to a wall and held...

    1-A 10 m long bar is attached by a frictionless hinge to a wall and held horizontal by a rope that makes an angle of 53 with the bar. the bar is uniform and weights 40N. a)how far from the hinge should a 10 kg mass be suspended for the tension T in the rope to be 100 N? b) determine the vertical component of the force exerted by the hinge on the bar. --------------------------------------------------------------------------------------------------------------------------------------------------------------------- 2- A traffic light hangs...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT