Q1) Design parameter that apply to two gear in mesh
Answer - Pressure angle
Other design parameters that are considered during gear design is Module and No. of teeth.
Q2) Stages required for Gear ratio of 110:1 for spur or helical gears
The maximum gear ratio for spur gears - 7:1
The maximum gear ratio for Helical gears - 10:1
So, 110/7 = 15.71 or 110/10 = 11
So approximately, answer = 12
Q3) The reverted gear train is one in which the input and output shafts on coincident.
It has two shafts and two gear pairs.
Q4) True
The center distance can be given as C = r1 + r2 = (d1 + d2) /2
Where r1 and r 2 are radius of pinion and gears respectively and d1 and d2 are their diameters
P = Diametrical pitch = Z/d
where Z = no of teeth
C = Z1 + Z2 / 2 P
So centre distance is a function of pitch and teeth
Q5) IV - Design parameters for specific pitch
Pressure angle, No of teeth, Power or Torque to be transmitted, Module.
V - constraints
Geometrical constraints
1. Coaxial constrain
2. Face width constrain
Kinematic Constraints
3. Gear ratio
Strength constraints
4. Beam strength
5. Wear strength
Please answer all the mcqs Question 1 (1 point) Select from the following list the design...
Design Problem Design a speed reducer gear box that will take 1.5 kW power from an electric motor rotating at 3000 rpm (clockwise) and deliver it to a machine which operates at 2 different speeds, 1000 rpm (clockwise) and 500 rpm (counter-clockwise). Use Spur Gears with 20° pressure angle and 5mm module. Gear box should be of smallest possible size. The gear shift mechanism is not the part of the design A 2-speed double-reduction speed reducer is shown in the...
kinematics please answer ASAP 2 (20 points) Design a compound, reverted, 20° standard spur gear train for a gear ratio of 70:1 . (a) Specify the teeth numbers (2 18 for the pinions); (b) With the diametral pitch of 10 for all gears, calculate their outside diameters and the contact ratio for the pair with the larger gear ratio. 2 (20 points) Design a compound, reverted, 20° standard spur gear train for a gear ratio of 70:1 . (a) Specify...
2. (20 points) Design a compound, reverted, 20 standard spur gear train for a gear ratio of 70:1. (a) Specify the teeth numbers (2 18 for the pinions); (b) With the diametral pitch of 10 for all gears, calculate their outside diameters and the contact ratio for the pair with the larger gear ratio. 2. (20 points) Design a compound, reverted, 20 standard spur gear train for a gear ratio of 70:1. (a) Specify the teeth numbers (2 18 for...
Problem 1. Design a reverted gear train for a transmission with three speeds and reverse. For an input speed of 450 rpm to the driving shaft (green), the driven shaft (teal) should have output forward speeds of 75, 300, and 450 rpm, and an output reverse speed of 150 rpm. Assume all gears have a diametral pitch of 10. Gear A (24 teeth) and Gear D (36 teeth) are in constant mesh. Determine the numbers of teeth for ALL six...
Show all work. A compound reverted gear train will be used to decrease speed with a ratio of 36 to 1. In the figure below, the input shaft drives gear 5, and the output shaft is driven by gear 2. Use spur gears with a 20 degree pressure angle and a diametral pitch of 5 teeth / in. a) Specify the appropriate numbers of teeth for both gear sets to minimize the gearbox size, while also avoiding gear tooth interference....
You work for a gearbox company and have been charged with helping to design a geared countershaft for a speed reducing gearbox. The gearbox consists of a compound reverted gear train as shown below and is to be designed for an exact 16:1 speed reduction ratio. The input motor provides 10-horsepower which is carried through the gear train and operates at a speed of 2,000 rpm. You are asked to consider spur gears with a 20° pressure angle and 4...
2. Consider the triple speed reduction gear box shown in Figure 1. All the gears are made with a diametral pitch of 16 in. The input of the gear train is gear A, and the output is gear G. The gear train transmits an input toque of 250 lb-in, at a speed of 2,500 rpm clockwise. The number of teeth on each gear is given as follows: NA 24 teeth, Na = 60 teeth, Nc 20 teeth, No 58 teeth,...
Question 1 - (20 Marks) (a) Explain the following terms: i. Spur gear ii. Velocity ratio (VR) of two spur gears iii. Gear train [2 mark] [2 mark] [2 mark] (b) Design the spur wheels, having a velocity ratio of 4 and the pitch of teeth as 8 mm. The approximate distance between the two shafts is 350 mm. 114 marks Question 2 - (20 Marks) Bar AB in Figure Q2 rotates at 5 rad/s in the clockwise direction. (a)...
power = 3 kW if need any more information please ask !!! You are the designer and you have been asked to design a speed reducer (gearbox) that will take power from the shaft of an electric motor rotating at 1500 rpm and deliver it to a machine that is to operate at approximately at 200 rpm Assume that you have decided to use spur gears to transmit the power [A power equal to the last one digits of your...
please don't copy and paste from previous answer Figure 4 shows a six-element planetary transmission, where spur gears 1 and 2 have an mi module, spur gears 3 and 5 have an m2 module, and spur gears 4 and 6 have an mj module. a. Write the train output velocity (Op) formula as a function of the angular velocity of shafts A, B and C, and tooth numbers Ni to No b. Establish the angular velocity of the output shaft...