A 1.2 V-range analog signal is sampled by an 8-bit digitizer. What is the least significant bit?
If the least significant bit in a different system is 10µV, what is the smallest change you can sample, according to the Nyquist Theorem?
1)Range =1.2 v
8 bit ADC,
=4.658 mV
2)As the system 1LSB =10 microvolt,
According to Nyquist sampling theorem, =2(LSB)
=20 microvolt
A 1.2 V-range analog signal is sampled by an 8-bit digitizer. What is the least significant...
An 10-bit analog-to-digital converter (ADC) has a voltage range of 0 to 12 V and a digitization uncertainty of ±1 LSB. What is the maximum uncertainty if the digitization is for a 12 V signal? What is the maximum uncertainty for a 18-bit ADC, and for 43-bit? If this ADC has a conversion time of 73 μs, then what is the highest frequency that can be accurately digitized while satisfying the Nyquist criterion? Answer with proper significant figures.
*5. Suppose an analog signal has an absolute bandwidth of 10 KHz. It is sampled at the Nyquist rate and converted to a digital signal using an A/D converter such that the output signal-to-quantization noise ratio is at least 40 dB. Using your engineering judgment, choose the number of bits for the A/D converter and determine the bit rate (i.e., the number of bits/sec).
Given an analog signal ?? (?) = 10 cos(3500??) , ??? ? ≥ 0, sampled at a rate of 8 kHz. Determine the expression for the spectrum ?(?) of the sampled signal and plot the spectrum of the sampled signal. You can use MATLAB wvtool for spectrum plot. Is there any aliasing?
1. An A/D converter will convert voltages over a 0 to 10 V range. How many bits must it be to achieve a 1 mV resolution over the entire range? 2. You have an A/D converter that will convert over a range of 0 to 5 V. You input an analog signal to it that has a range of 1 to 3.5 V. What must be the number of bits of the converter to achieve a resolution of 1% of...
A video signal has bandwidth of 4 MHz. This signal is sampled, quantized, and binary encoded using the PCM technique. The video signal amplitude is uniformly distributed in the range (-2, 2). If the signal is sampled at the Nyquist rate and quantized into 512 levels: (a) Determine the bit rate. (b) Determine the signal-to-quantization-noise ratio. (©) If the signal-to-quantization-noise ratio must be increased by a factor of 16, how you can achieve that? Will this affect the bit rate?...
An analog signal is given as below x(t) = 10sin 4rtt The signal is sampled by two different frequencies f, = 1Hz, f, = 10Hz respectively, and the output are yı, Yz. (i) Sketch signal x(t) in the time domain. (3 marks) (ii) Sketch frequency spectrum of x(t). (3 marks) (iii) After sampling, the continuous signal is converted to a discrete signal. Draw the two discrete signals Yı, Y2: (4 marks) (iv) Discuss whether f1, f, can successfully sample the...
Question 2 An analog signal with a power Pm-GW, and a bandwidth of 4kHz is sampled at a rate f, = 10ksamples/sec. (a) What value of A will lead to an SQNR of 55dB if uniform quantization is used? (b) If the peak voltage of m(t) is 8V, what value of L satisfies (a)? (c) How many bits per sample should be used? (d) What is the bit rate if we use the number of bits per sample from (c)?...
When designing an Analog to Digital System all of the range values for the system must be defined from input to output. This input will be used to drive a 3. PWM output signal to operate an LED. Assume the PWM is calibrated to read minimum to maximum based on the binary input range given. Potentiometer - 10 KS2 (0 degrees to 180 degrees) VDC for Potentiometer 12 V Analog Converter Module 10 bit, Vref 8 V PWM Module-8 bit,...
1- A12 bits analog to digital converter (ADC) has a sampling rate of IMHz. If the analog signal has a range of 5V, a) How many different digital values can this ADC outputs? (20 POINTS) b) What are the smallest and largest possible outputs of this ADC? c) What is the voltage/bit resolution? d) If an application requires 1u V/bit resolution, how m ADC have? ny bits should the
If an analog temperature sensor is used with an 8 bit ADC (analog to digital converter) and a 5 volt power source, what is the smallest temperature increment you could measure? That is, what is the resolution here?