If a three-phase load is a pure reactive load, then the power calculated has units of...
A balanced wye-connected load and a balanced delta con- hected load are supplied by a three-phase 480-V 50 HZ generator. The ranch impedance of the wye and della are 10/30° 2 and 20/-50° 2. respectively. Determine the active and reactive powers drawn by each three loads. Determine the phasor voltage and phase any one branch of each three-phas e branch of each three-phase load, and substitute into wer equation for balanced three-phase loads. Given ise angle of V is 30...
UISIZULU Problem 4 A three phase, 5 kW, wye-connected load operate onnected load operates at 0.8 power factor lagging with a terminal voltage of 100 V (line to line). The cables connecting e bles connecting each phase of the load to the wye-connected supply has an impedance of (0.25 +0.25) 12. Compute the following: a) Reactive power drawn by the load. b) Real and reactive power losses in the system. me current and line voltage at the source terminals and...
52. In three-phase power systems, the delivered power a. falls to zero three times per cycle b. falls to zero once per cycle c. never falls to zero d. none of the above 53. The three-phase connection in which one end of each of the windings are connected together is called the connection. a. delta b. wye c. open delta d. open wye 54. In a three phase connection, the voliage meaured direety across one of the winings is the...
4-9
Question Completion Status: QUESTION 4 A three phase delta source is connected to a three phase transformer. The primary of the transformer is connected in a delta configuration The line voltage on the primary is 240V. The turns ratio is 2:1. The secondary of the transformer is connected in a wye configuration. A wye connected load is attached to the secondary of the transformer. Each of the three load resistors has a resistance of 10 ohms. What is the...
A three-phase electrical heater dissipates 50kW when connected to a 4160V, 3-phase line. (a) Draw the circuit diagram and indicate system parameters (line to line voltage, currents, fuses, etc.) if the loads (resistors) are connected in WYE. (b) What is the LINE current if the resistors are all connected in WYE? (c) Draw the circuit diagram and calculate the LINE current if the resistors are all connected in DELTA? (d) While the delta connected load resistors are working fine, and...
Question 2: Three phase circuit. (100p) A wye connected generator supplies a delta connected balanced load through short feeder. seree the load line to neutral voltage as reference voltage phase angle zero. 02.1 Q2.2 Q2.3 Q2.4 Draw the equivalent circuit. 10p Calculate the load line-to-neutral voltages and line-to-line voltages. 20p Calculate the delta load currents and feeder currents. 20p Calculate the supply wye connected generator line-to-neutral voltages. Is the obtained values are acceptable? Calculate the generator real and reactive power...
508 CHAPTER 11 . POLYPHASE CIRCUITS 11.40 In a balanced three-phase system, the source has an aboc phase-sequence and is connected in delta. There are two rallel wye-connected loads. The phase impedance of load i and load 2 is 4 The line impedance connecting the source to the loads is 0.3 + j0.2 2. If the curre IAN! = 10/20-Arms, find the delta currents in the source 4 Ω and 10 +/4 Ω, respectively. nt in the a phase of...
2. Two balanced three-phase loads are connected in parallel. One load with per phase impedance 21 ?, is connected in delta, and the other load has per phase impedance 15 2 and is connected in wye. Ignore the line impedance. If the line voltage is a 208230° Vrms, determine (a) the phase voltage for phase-a, ) the line current Ia*, (c) the phase currents in the delta load (d) the complex power of the load and the power factor.
3- A balanced wye-connected load of (4 + j3) Ω is connected across a three-phase delta connected source. the source phase voltage is 173 V . • Find the load current. • Find the power factor, P and Q
A balanced delta connected load has a per phase
impedance of 12+j21 ohms. The load is supplied power from a source
with line to line voltage of 480 V through a distribution line. The
line impedance is 2 + j4.5 ohms. What is the current magnitude in
the distribution line?
of the below questions. A balanced A connected load has a per-phase impedance of 12+,21 22. The load is supplied power from a source with line-to-line voltage of 480 V...