Rectifier Circuit Assume for the circuits there is a simple resistive load R and an AC...
Rectifier Circuit
Assume for the circuits there is a simple resistive load R and an
AC source with an amplitude of 5 V (rms).
Zener - 1N749A
V1 - 4.3 V
Vs - 5 V
a.) Draw the wiring diagram for an unfiltered, half-wave
rectifier circuit.
b.) Draw the wiring diagram for a filtered, half-wave
rectifier.
Homework Answers
Add Answer to:
Rectifier Circuit
Assume for the circuits there is a simple resistive load R and an
AC...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
A single phase half-wave SCR rectifier is used to reduce the average voltage across a nonlinear...
A single phase half-wave SCR rectifier is used to reduce the
average voltage across a nonlinear resistive load where the
resistive value is represented by
R = 0. 2 V^2(aver) + 5 Ω
Calculate the load average current when the source voltage is
110 V RMS and the triggering angle is 90 degrees
A single phase half-wave SCR rectifier is used to reduce the average voltage across a nonlinear resistive load where the resistive value is represented by aver Calculate...
1. A 50 Hz 3-phase Have wave uncontrolled rectifier circuit is used to supply a resistive load of...
1. A 50 Hz 3-phase Have wave uncontrolled rectifier circuit is used to supply a resistive load of 100 ohms. The supply is unbalanced and defined as v.-127.28 cos (ot) V 127.28 sin (ot-0.5236) V n63.64 cos (ot+2.0944) V a) Draw the circuit diagram. b) Draw the three phase voltages wave forms. c) Use phasor diagram or any other method to obtain the line voltages v and d) Draw the line voltages v and v wave forms. e) Derive an...
Exercise#2 • An AC supply of 230V rms is applied to a half wave rectifier circuit...
Exercise#2 • An AC supply of 230V rms is applied to a half wave rectifier circuit through a transformer of turn ratio 5:1. Assume the diode is an ideal one. The load resistance is 30092. * Find (a) peak load current (b) the dc load current (c) the rms load current (d) TUF (e) PIV (f) FF (g) RF (h) power delivered to load
i want the answer with detales Single-Phase Controlled Rectifier Exercise Derive the expressions of the average...
i want the answer with detales
Single-Phase Controlled Rectifier Exercise Derive the expressions of the average load voltage and current in single-phase half-wave controlled rectifiers and resistive load. Draw the waveforms of supply voltage. output voltage, output current, thyristor voltage and thyristor current Exercise In a single-phase half-wave controlled rectifier and resistive kad, it is desired to get an average load voltage of 80 V. Determine the firing angle if the ac supply voltage is 230 V. If the load...
A controlled half-wave rectifier has an RL load with R 20 ohm and L 40 mH....
A controlled half-wave rectifier has an RL load with R 20 ohm and L 40 mH. The source is 120 V rms at 60 Hz The delay angle required to produce an average current of 2.0 A I output RMS I input RMS Apparent power and power factor Skitch Vout, Iout, and V diod
please help Question 1 Consider the following circuit, where the reverse saturation current (Is) is the...
please help
Question 1 Consider the following circuit, where the reverse saturation current (Is) is the same for each diode. D2 o Vo Di Vi WWW R 32 23 a. b. Determine an algebraic expression for V1, for a given Vo, and Is. Given an Is of 40 FA and R1 = 3.3 kl , determine the Vi that produces an output voltage (V.) of 0.625 V. C. Recalculate question-b if Is were to be a thousand times greater at...
A full-wave diode rectifier supplies a 30Ω resistive load from a 400Hz, 110V single-phase AC supply....
A full-wave diode rectifier supplies a 30Ω resistive load from a 400Hz, 110V single-phase AC supply. A capacitor is connected in parallel with the load. Calculate the capacitance required if the maximum peak-to-peak voltage ripple across the resistor is to be restricted to 10V. You may assume that the RC product of the resistance and capacitance will be significantly greater than the period of the AC waveform. State any other assumptions made.
It is required to use a FULL-wave rectifier to design a dc power supply that provides...
It is required to use a FULL-wave rectifier to design a dc power supply that provides an average dc output voltage of 15 V. A maximum ripple voltage of ±1 V is allowed on the output voltage. The output voltage will feed a load resistance of 250 Ω. Assume a sinusoidal input voltage with the frequency of 60 Hz. Do not include a Zener diode in your design. (Assume V_D0)* = 0.7 V). a) Draw the circuit diagram. b) Calculate...
2. Rectifier with zener diode Given: Simple AC powered voltage reference source with following parameters: D1...D4...
2. Rectifier with zener diode Given: Simple AC powered voltage reference source with following parameters: D1...D4 R1 Vout Vin SEC V sec=10 V (RMS) fset=60 Hz Vp=0.6 V (each) ZD=5.6 V / 10 mA C= 10 uF VREF= 5.6 V ☆ Calculate: R1 V Ripl
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
A single phase half-wave SCR rectifier is used to reduce the
average voltage across a nonlinear resistive load where the
resistive value is represented by
R = 0. 2 V^2(aver) + 5 Ω
Calculate the load average current when the source voltage is
110 V RMS and the triggering angle is 90 degrees
A single phase half-wave SCR rectifier is used to reduce the average voltage across a nonlinear resistive load where the resistive value is represented by aver Calculate...
1. A 50 Hz 3-phase Have wave uncontrolled rectifier circuit is used to supply a resistive load of 100 ohms. The supply is unbalanced and defined as v.-127.28 cos (ot) V 127.28 sin (ot-0.5236) V n63.64 cos (ot+2.0944) V a) Draw the circuit diagram. b) Draw the three phase voltages wave forms. c) Use phasor diagram or any other method to obtain the line voltages v and d) Draw the line voltages v and v wave forms. e) Derive an...
Exercise#2 • An AC supply of 230V rms is applied to a half wave rectifier circuit through a transformer of turn ratio 5:1. Assume the diode is an ideal one. The load resistance is 30092. * Find (a) peak load current (b) the dc load current (c) the rms load current (d) TUF (e) PIV (f) FF (g) RF (h) power delivered to load
i want the answer with detales
Single-Phase Controlled Rectifier Exercise Derive the expressions of the average load voltage and current in single-phase half-wave controlled rectifiers and resistive load. Draw the waveforms of supply voltage. output voltage, output current, thyristor voltage and thyristor current Exercise In a single-phase half-wave controlled rectifier and resistive kad, it is desired to get an average load voltage of 80 V. Determine the firing angle if the ac supply voltage is 230 V. If the load...
please help
Question 1 Consider the following circuit, where the reverse saturation current (Is) is the same for each diode. D2 o Vo Di Vi WWW R 32 23 a. b. Determine an algebraic expression for V1, for a given Vo, and Is. Given an Is of 40 FA and R1 = 3.3 kl , determine the Vi that produces an output voltage (V.) of 0.625 V. C. Recalculate question-b if Is were to be a thousand times greater at...
2. Rectifier with zener diode Given: Simple AC powered voltage reference source with following parameters: D1...D4 R1 Vout Vin SEC V sec=10 V (RMS) fset=60 Hz Vp=0.6 V (each) ZD=5.6 V / 10 mA C= 10 uF VREF= 5.6 V ☆ Calculate: R1 V Ripl
Most questions answered within 3 hours.
-
The mayor of a town has proposed a plan for the construction of
a new community....
asked 7 minutes ago -
2. KopyKat is a firm that specializes in printing business cards
using the latest laser technology....
asked 27 minutes ago -
What type of stock pays dividends in arrears?
A.
Nonminus−cumulative
preferred stock
B.
Cumulative preferred stock...
asked 25 minutes ago -
Discuss what issues you see as needing to be addressed in an
organization in order to...
asked 27 minutes ago -
Why does varying input frequency to a buck converter affect the
magnitude of the output voltage...
asked 30 minutes ago -
Given the following reduction half-reactions:
Fe3+(aq)+e−→Fe2+(aq)
E∘red=+0.77V
S2O2−6(aq)+4H+(aq)+2e−→2H2SO3(aq)
E∘red=+0.60V
N2O(g)+2H+(aq)+2e−→N2(g)+H2O(l)
E∘red=−1.77V
VO+2(aq)+2H+(aq)+e−→VO2+(aq)+H2O(l)
E∘red=+1.00V
Write balanced chemica
asked 31 minutes ago -
Consider a random variable X with PDF given by f(x)=1/10 for x =
0, 1, 2,...,9....
asked 29 minutes ago -
This is QA Tester's task
What was the most heinous bug that you let slip through?...
asked 42 minutes ago -
What is the chemical equation (with states) for this
reaction in balanced and unbalanced form?
In...
asked 46 minutes ago -
In engineering and product design, it is important to consider
the weights of people so that...
asked 51 minutes ago -
The first-order decomposition of N2O5 at 328 K has a rate
constant of 1.70 × 10-3...
asked 53 minutes ago -
Do you believe that some things that fall into the category of
“pseudoscience” are worth believing...
asked 1 hour ago