The diagram below shows a cruise control system for a car. VD (s) V(s) ms 89 (a) Find the open lo...
Problem 3 A boat of mass m glides through the water, experiencing viscous fluid resistance with damping coefficient b. The diagram below shows the control system using a PD controller for the motor. 1n XD (s) 1 X(s) (a) Find the open loop transfer function. (b) Find the closed loop transfer function. (c) This can be modeled as a second order system so its closed loop transfer function fits the form: Cs C2 If a dam ping ratio of ζ...
Question 6 The open-loop transfer function G(s) of a control system is given as G(8)- s(s+2)(s +5) A proportional controller is used to control the system as shown in Figure 6 below: Y(s) R(s) + G(s) Figure 6: A control system with a proportional controller a) Assume Hp(s) is a proportional controller with the transfer function H,(s) kp. Determine, using the Routh-Hurwitz Stability Criterion, the value of kp for which the closed-loop system in Figure 6 is marginally stable. (6...
P4: The car model of a cruise control system is given in the following transfer function block diagram ms + b Where v is the car speed u is the control force m is the mass of the vehicle, 1000 kg b is the damping coefficient, 50 N s/m More details are available here (1) Derive the differential equation relating y(t) to u(t) (2) Determine the time constant of the car dynamics (from u to v) If a proportional feedback...
show steps please 10 A second-order open-loop system with transfer function G(s) = is to be $2+45+10 controlled with unity negative feedback. (a) Derive the error transfer functions E(s) of the closed-loop system subjected to a unit step input, when using a P controller and a PI controller, respectively, in terms P control gain kp, and PI control gains kp and ki, respectively. [7] (b) Determine the steady-state errors in (a). Briefly comment on the differences in control performance by...
4.35 Consider the feedback control system with the plant transfer function G(s) = (5+0.1)(5+0.5) (a) Design a proportional controller so the closed-loop system has damping of 5 = 0.707. Under what conditions on kp is the closed-loop system stable? (b) Design a PI controller so that the closed-loop system has no over- shoot. Under what conditions on (kp, kt) is the closed-loop system is stable? (©) Design a PID controller such that the settling time is less than 1.7 sec.
Consider a unity-feedback control system with a PI controller Gpr(s) and a plant G(s) in cascade. In particular, the plant transfer function is given as 2. G(s) = s+4, and the PI controller transfer function is of the forrm KI p and Ki are the proportional and integral controller gains, respectively where K Design numerical values for Kp and Ki such that the closed-loop control system has a step- response settling time T, 0.5 seconds with a damping ratio of...
Answer Questions 7 through 13 using the diagram below. 7. Open Loop Transfer Function 8. Closed Loop Transfer Function 9. Characteristic Equation 10. Damping Factor 11. Natural Frequency in rad/sec 12. Is the system over-, under-, or critically-damped?_ 13. What is the Error Coefficient and Steady-State error of the system? Error Coefficient Steady-State error h=0.25 14. Given the following parameters for a position control system: Step input of 2 radians; Kp = 4, Ka = 20, Km = 8, h...
question b or the control system in Figure 1: C(s) Find the closed-loop transfer function T(s)-- R(s) a) b) Find a value of Kp that will yield less than 15% overshoot for the closed-loop system. (Note: ignore the zero dynamics to calculate Kp initially). c IIsing vour K from nart h) write a MATI AR scrint that calculates the closedloon Motor Plant R(s)+ C(s) Controller 10 Kp (s+9) s2 +6s15 12 Figure 1: Unity feedback with PD control or the...
Q3. Consider a single loop unity feedback control system of the open loop transfer function (a) Find the range of values of the gain K and the parameter p so that: (i) The overshoot is less than 10%. (ii)The settling time is less than 4 seconds Note: , 4.6 M. = exp CO 40% (b)What are the three elements in a PID controller? Considering each in turn, explain the main ways in which varying the parameters affects the closed-loop system...
5. The open loop transfer function of a control system is s(1 +0.5s)(1 0.67s) Draw a Bode diagram for the system and determine the phase margin and gain margin. Is the closed loop system stable? (a) (17 marks) (b) By how much must the gain be adjusted for a phase margin of 50°? (8 marks) 5. The open loop transfer function of a control system is s(1 +0.5s)(1 0.67s) Draw a Bode diagram for the system and determine the phase...