How many #4/0 AWG type XHHW conductors will fit into a Trade Size 3 ½ Electrical Metallic Tubing,...

Question

Question

How many #4/0 AWG type XHHW conductors will fit into a Trade Size 3 ½ Electrical Metallic Tubing, EMT, conduit?

Answer 1

Answer #1

14 XHHW conductors of 4/0 AWG type will fit into the TRADE size 3 1/2 Electrical Metallic Tubing , EMT , Conduit

AS PER ............................... NEC ( National Electric Code) of year 2017 refrence tables C1, C4 and C8

Answer 2

Similar Homework Help Questions

If 22 - #6 AWG type THHN Copper conductors are placed in a single Electrical Metallic...

If 22 - #6 AWG type THHN Copper conductors are placed in a single Electrical Metallic Tubing, EMT, conduit, the ampacity must be de-rated by what percent for this number of conductors?
D. trade size 1 1/2 (41). Atrade size 4 (21). B.trade size 1 (27). (53). Ctrade size 1 1/4(35). E. trade size 2 Cod...

D. trade size 1 1/2 (41). Atrade size 4 (21). B.trade size 1 (27). (53). Ctrade size 1 1/4(35). E. trade size 2 Code reference 29. The general use 125-volt receptacles in a commercial building are supplied by 20- ampere rated multiwire branch-circuits with three ungrounded conductors anda common neutral from a 208/120-volt, 4-wire, 3-phase electrical system. The con ductors for nine circuits are run in a single raceway to an area of the building includ ing nine ungrounded conductors...
Ten #3 AWG copper load carrying conductors with type THHW, 75oC insulation are installed in a...

Ten #3 AWG copper load carrying conductors with type THHW, 75oC insulation are installed in a rigid metal conduit, RMC. What is the final loaded allowable ampacity for each conductor?

How many 14 AWG THW conductors are permitted in a 3 in x 2 in x...

How many 14 AWG THW conductors are permitted in a 3 in x 2 in x 2 1/2 in device box
pleas help me in this do any question you know using National Electrical Code 2011 Applied Electricity NEC...

pleas help me in this do any question you know using National Electrical Code 2011 Applied Electricity NEC worksheet t hree Copper conductors with THHN insulation run in Electrical A branch-circuit Consther conductors. The conductor terminations are rated for a maximum ure in the area of this installation is not expected to exceed 30C size 8 AWG, the maximum ampacity of the conductors If the conductors for this circuit are permitted A 40 amperes. B. 50 amperes. to be used...
What size Intermediate Metal Conduit is required for Four (4) #600 kcmil Type THW Conductors? A....

What size Intermediate Metal Conduit is required for Four (4) #600 kcmil Type THW Conductors? A. 2" B. 2 1/2" C. 3" D. 3 1/2" E. 4" F. 5" G. 6" What is the minimum number of duplex outlets required along a 32 foot living room wall? A. 2 B. 3 C. 4 D. 5 E. 6 F. 7 G. 8 H. 9

O AWG copper conductor without any markings to indicate the The terminal for dh s terminal is assumed to have a min...

O AWG copper conductor without any markings to indicate the The terminal for dh s terminal is assumed to have a minimum terminal temperature rating E. 90°C. 60°C. of: C, D. 75 C. B. 40-С. Code reference re rated branch-circuit supplies fluorescent luminaires (lighting fixtures) with a peres. All terminations are 75°C rated, there are only three current- THHW as shown in Figure 1.43 pe 10. A 20-am carrying conductors in EMT, and the conductor insulation is The minimum size...
Calculate the measure electrical output (mA) of a pressure-type level sensor that has a 0-4 psi...

Calculate the measure electrical output (mA) of a pressure-type level sensor that has a 0-4 psi input range and a 0-20 mA output range if the pressure sensed is 3 psi.
1. The color of the outer finish of the insulation or tape marking a grounded conductor...

1. The color of the outer finish of the insulation or tape marking a grounded conductor must be A. black B. green. C. white or gray D. yellow finish. 2. When the main bonding jumper in a residential el ectrical system is a screw only, the screw must be identified with a A. white B. red C. green D. black The grounding electrode conductor should be installed without a splice, unless the splice is made using exothermic welding or by...

Electrical Knowledge: 1. Know what a multimeter is and how to use it. 2. Know how to field check a 3-phase AC motor for...

Electrical Knowledge: 1. Know what a multimeter is and how to use it. 2. Know how to field check a 3-phase AC motor for proper operations. 3. Know grounds and shorts, and the proper way to test for them. 4. Be able to calculate current if given the number of volts and the amount of resistance in ohms. 5. Know about electrically operated control valves and how to troubleshoot if it will not actuate the valve. 6. Know the different...