Homework Answers
Add Answer to:
IV Figure 1: Schematic of forward converter with a reset winding uestions: (10 Pts) 1. Complete t...
1) For a buck-boost converter, it is desired to have a peak-peak capacitor ripple (vc.pP) of 50 m...
1) For a buck-boost converter, it is desired to have a peak-peak capacitor ripple (vc.pP) of 50 mV fora converter operating at 100 kHz and with a output current of iOUTAVG 10 A. Assume the input is between Total: 6 pts) (3 pts) (3 pts) VIN= [10, 22.5] and the output is fixed at-15 V. Select (and prove) the capacitance C to accomplish this. Verify your result with using PSIM (assume L = 200 μH). a. b. - VD1 21...
a9a resistive load. Inductor 3-(35 pts) Design a converter that has an input voltage of 24 V DC and supplies 18 V DC to current is desired to be continuous and must not change more than 30 % of i...
a9a resistive load. Inductor 3-(35 pts) Design a converter that has an input voltage of 24 V DC and supplies 18 V DC to current is desired to be continuous and must not change more than 30 % of its average value voltage ripple must be lower than 2 %. Switching frequency is 10 kHz. a) Draw the circuit diagram. Calculate the duty ratio. Calculate values for 2 desired conditions of the inductor current and determine the value of the...
A buck converter is used to have low output voltage from the high input source to...
A buck converter is used to have low output voltage from the high input source to low output voltage. The estimated power output is at 25 kW with the switching frequency of 25 kHz. Design the buck converter as by finding and following specifications consider the ripple of the output is set at 1% (i) Calculate the duty ratio of the buck converter (1 mark) (ii) Determine the minimum requirement for the inductor and the capacitor (5 marks) (iii) Determine...
Problem 3: (20 points) Design a suitable power converter (only the power stage) for the following...
Problem 3: (20 points) Design a suitable power converter (only the power stage) for the following specifications Input voltage: 36 V to 72 V; required output voltage: 48 V regulated; load current: 2 A to 10 A Maximum allowable pk-pk output ripple voltage: 0.5 V; maximum allowable pk-pk ripple in any inductor current: 2 A. Assume a switching frequency of 200 kHz. Show a complete schematic and the following details in your answer. L: Minimum L value C: Minimum C...
****Please ALL answers questions with complete steps.**** 1. Analysis and design of a buck-boost converter. A...
****Please ALL answers questions with complete
steps.****
1. Analysis and design of a buck-boost converter. A buck-boost converter is illustrated below. + licit) + reee c= R { v(t) A practical implementation using a MOSFET and diode is illustrated below. D + Voi(t) – H + iqi(t) IT int) lic(t) iz(t) + LE vi(t) c R v(t) For this problem, you must employ the methods of inductor volt-second balance, capacitor charge balance, and the small ripple approximation as discussed in...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage 12 V. Switching frequency is 15 kHz. Calculate duty ratios for the switch and the diode. Find values for the inductor L and capacitor C, when the allowed output voltage ripple is ±0.15 % and the inductor current ripple is ±1 % (of the average value). If the on-time of the switch has an inaccuracy of ±50 ns, what is the new output voltage...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Question 9 10 pts The transformer of a forward converter will operate at 50 kHz and the coil voltages are V1-V2-V3-90-V. The RMS current in each winding is 5.87-A. For a current density of 4.7 determ...
Question 9 10 pts The transformer of a forward converter will operate at 50 kHz and the coil voltages are V1-V2-V3-90-V. The RMS current in each winding is 5.87-A. For a current density of 4.7 determine the diameter of the coil wire.
Question 9 10 pts The transformer of a forward converter will operate at 50 kHz and the coil voltages are V1-V2-V3-90-V. The RMS current in each winding is 5.87-A. For a current density of 4.7 determine the diameter...
Please answer 2 and 1. Assignment No.6 10mH, C-20μF, an 1. A boost converter as the...
Please answer 2 and 1.
Assignment No.6 10mH, C-20μF, an 1. A boost converter as the following parameters: V,-20V, L Find the current spec of the inductor for continuous current mode (Max an Min current) -20 2. Switching frequency is 50 KHz and conduction duty cycle is 0.6 a. b. Calculate the output voltage and the ripple voltage An array has been formed with three modules in a string and two strings in parallel. The overall characteristic of the array...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 ...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
1) For a buck-boost converter, it is desired to have a peak-peak capacitor ripple (vc.pP) of 50 mV fora converter operating at 100 kHz and with a output current of iOUTAVG 10 A. Assume the input is between Total: 6 pts) (3 pts) (3 pts) VIN= [10, 22.5] and the output is fixed at-15 V. Select (and prove) the capacitance C to accomplish this. Verify your result with using PSIM (assume L = 200 μH). a. b. - VD1 21...
a9a resistive load. Inductor 3-(35 pts) Design a converter that has an input voltage of 24 V DC and supplies 18 V DC to current is desired to be continuous and must not change more than 30 % of its average value voltage ripple must be lower than 2 %. Switching frequency is 10 kHz. a) Draw the circuit diagram. Calculate the duty ratio. Calculate values for 2 desired conditions of the inductor current and determine the value of the...
A buck converter is used to have low output voltage from the high input source to low output voltage. The estimated power output is at 25 kW with the switching frequency of 25 kHz. Design the buck converter as by finding and following specifications consider the ripple of the output is set at 1% (i) Calculate the duty ratio of the buck converter (1 mark) (ii) Determine the minimum requirement for the inductor and the capacitor (5 marks) (iii) Determine...
Problem 3: (20 points) Design a suitable power converter (only the power stage) for the following specifications Input voltage: 36 V to 72 V; required output voltage: 48 V regulated; load current: 2 A to 10 A Maximum allowable pk-pk output ripple voltage: 0.5 V; maximum allowable pk-pk ripple in any inductor current: 2 A. Assume a switching frequency of 200 kHz. Show a complete schematic and the following details in your answer. L: Minimum L value C: Minimum C...
****Please ALL answers questions with complete
steps.****
1. Analysis and design of a buck-boost converter. A buck-boost converter is illustrated below. + licit) + reee c= R { v(t) A practical implementation using a MOSFET and diode is illustrated below. D + Voi(t) – H + iqi(t) IT int) lic(t) iz(t) + LE vi(t) c R v(t) For this problem, you must employ the methods of inductor volt-second balance, capacitor charge balance, and the small ripple approximation as discussed in...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Question 9 10 pts The transformer of a forward converter will operate at 50 kHz and the coil voltages are V1-V2-V3-90-V. The RMS current in each winding is 5.87-A. For a current density of 4.7 determine the diameter of the coil wire.
Question 9 10 pts The transformer of a forward converter will operate at 50 kHz and the coil voltages are V1-V2-V3-90-V. The RMS current in each winding is 5.87-A. For a current density of 4.7 determine the diameter...
Please answer 2 and 1.
Assignment No.6 10mH, C-20μF, an 1. A boost converter as the following parameters: V,-20V, L Find the current spec of the inductor for continuous current mode (Max an Min current) -20 2. Switching frequency is 50 KHz and conduction duty cycle is 0.6 a. b. Calculate the output voltage and the ripple voltage An array has been formed with three modules in a string and two strings in parallel. The overall characteristic of the array...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
Most questions answered within 3 hours.
-
Two kg of ice at -15 °C are placed in a 2 kg bath of water...
asked 2 minutes ago -
Use the following set of observed frequencies to test the
independence of the two variables. Variable...
asked 2 minutes ago -
Please Identify the Term "Determinism" in Psychology
asked 1 minute ago -
Describe the following with suitable
examples.
1- Security Policy Heterogeneity
2-Security Model Heterogeneity
3-Security Mechanism Heterogeneity...
asked 3 minutes ago -
The table below represents the number of republicans, democrats
and independent voting on a specific issue....
asked 6 minutes ago -
List and compare different forms of passive transport and active
transport.
asked 14 minutes ago -
In Netherland Dwarf rabbits, dwarf size is determined by allele
N, and normal-size by allele n....
asked 21 minutes ago -
During Heaton Company’s first two years of operations, it
reported absorption costing net operating income as...
asked 35 minutes ago -
Consider testing the
hypotheses:
H0: p = 0.56
H1: p > 0.56
where p is
the...
asked 38 minutes ago -
In a two-factor analysis of variance a main effect is defined as
____.
a. the unique...
asked 46 minutes ago -
A bank's loan officer rates applicants for credit. The ratings
are normally distributed with a mean...
asked 46 minutes ago -
Fill in the following information for Adipic Acid: molecular
weight, g or ml, mole, melting point,...
asked 52 minutes ago