1. Given the state diagram shown below for a state machine with one-bit input W and two-bit output Z:
a. (20 points) Using the state assignments below, make the state-assigned table. Let S0 = 001, S1 = 010, and S2 = 100.
b. (20 points) Let the state variables be Y2, Y1, and Y0. Derive an expression for each of the next state variables.
c. (10 points) Derive expressions for the output of this state diagram.
d. (20 points) Draw the circuit which implements this state machine. Remember to add the reset connection.
e. (10 points) Is this a Moore state machine or a Mealy state machine? Why?
f. (20 points) Complete the timing diagram below for the state machine. Assume that the circuit/state machine starts off in state S0.
1. Given the state diagram shown below for a state machine with one-bit input W and two-bit outpu...
P6 (15 points): The FSM state diagram below has two inputs x1 and xo In addition, it has two DFFS, three 4-to-1 MUXes, a single XOR gate, a single AND gate, and a single output bit Z. Answer the following questions about this FSM. o/0 10/0 RESET A 61/0 C 9/0 01/0 1/0 o1/0 6/0 A: Is this a Moore FSM or a Mealy FSM? B: The state encodings are A-00, B-01, C-10, and D=11. Write a state- assigned table...
1. Given the state diagram shown below for a two-state synchronous sequential Mealy circuit with input. and output z, realize the circuit using D flip-flops. Your answer must include the state transition,excita- tion, and output tables, the excitation equation(s), and a labeled circuit diagram 1/0 2. Given the state diagram in Problem 1, realize the circuit using JK flip-flops. Your answer must include the state transition, excitation, and output tables, the excitation equation(s), and a labeled circuit diagram. 3. Given...
2. (20 points) Instead of using a Moore machine to implement the sequence detector in problem 1, derive a state diagram for a Mealy machine that will perform this operation. 1. (20 points) For this problem, we want to design a circuit that checks for the input sequence 00101. Your circuit will have a one-bit input W and a one-bit output Z where Z-1 if the last five values of W observed on each positive edge of the clock are...
A sequential circuit with two D Flip-Flops and one input X and one output Y is specifed by the following input equations: Y = A'+B DA = X + B DB = XA' (a) Draw the logic diagram of the circuit (b) Derive the state table. (c) Derive the state diagram. (b) Is this a Mealy or a Moore machine?
Part 1: Design a Moore state machine that recognizes both a 1012 and a 0102 input pattern. This state machine has a 2- bit wide z output. If the 1012 pattern is detected, the state machine should output 102. If the 0102 pattern is detected, the state machine should output 012. In the initial state, the output should be 002 and in all other states, the output should be 112. Draw the state diagram and the state table. Part 2:...
5) Decoders: Given the following circuit, S0 and S1 are computed using a 4-2 priority encoder with the priorities indicated on the figure. (hint: IDLE signal is always 0, if any of the inputs 10,11,12, or 13 is 1) 6 points) 4-to-2 Priority Encoder 10 YO YI 13 IDLE 13> 11 > 12>10 12 Full c Adder So Fill the following table showing the output signals S0 and SI given the input signals w, x, y, a) and z. Prof...
NAND Problem 3 (30 points) Consider the circuit shown alongside. Notice that there is one A input x and one output. FULL ADDER XOR (a) [5 points] Determine the B Q Cout Clk flip-flop input equations and xin the output z in terms of the present states A, B and input variable x in other words 4-1 compute T, J, K and z. MUX (b) [10 points] Use the above 1 equations to derive the state- 01 table. Assume the...
Q3. Consider the circuit shown below: Q1 Jo 0 Ko clock (a) Create the state table that shows the present-states, input x, JK flip-flops inputs, the next-states and the output y 30% (b) Create the state diagram, specify what type of state machine (Mealy or Moore) this circuit is and explain why 20%
Thc state transition table bclow is for a sequential circuit with onc input X and onc output Y. The circuit has two state variables A and B, and synchronous input Reset that resets the circuit to state AB-01 when Reset 1: Present State Next State Output X-0 A B A B 0 Reset State 0 0 (9 points) Implement the sequential circuit using minimum number of logic gates and rising- edge triggered D-FFs and draw the logic diagram of the...
Given the FSM schematic below, answer the following question Question 1. (30 POINTS) Given the FSM schematic below, answer the following questions: A, A CLK si s, Output 0 0 Reset 1.A.) (6 POINTS) What are the Boolean equations for next state and output logic? 1.B.) (4 POINTS) Is this a Moore or Mealy FSM? Why? Please explain. 1.C.) (10 POINTS) Draw the truth table for next state and output logic for this circuit. 1.D.) (10 POINTS) Draw the state...