Design a digital sine wave oscillator with f= 440 Hz, Sample rate = 5 kHz. Can the amplitude be adjusted without multiplication?
given that ;
f = 440Hz
sample rate = 5 kHz
#include <stdlib.h>
#include<math.h>
void main(void)
{
float Freq,t[5000],Fs, Amp;
Amp=1;
int i,j;
Freq=440; //Hz
Fs = 5000; //5KHz
for(i=0;i<5000;i++)
{
t = i;
t = t/5000;
SineWaveSignal = Amp * sin(2*PI*Freq*t)
}
}
}
Design a digital sine wave oscillator with f= 440 Hz, Sample rate = 5 kHz. Can the amplitude be adjusted without multiplication?
The oscilloscope display below is connected to a sine wave of 100 Hz frequency and 4 volt amplitude, 100 us seconds/div, and 2 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal into focus so that it displays a sine wave? The oscilloscope display below is connected to a sine wave of 150 Hz frequency , 2 ms seconds/div, and 1 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal...
assume we have converted an analog sine wave signal of frequancy equals to 250 hz and amplitude equals to 4 volts into a PCM digital signal of zeros and ones . consider that one period of the anloge sine wave can be represented by 18 samples after sampling process ,whereas the number of quantization level is 32 show all the drawing and calculate the and calculate the time duration of the analog sine wave signal
A 1 hz sine wave that starts at zero with amplitude zero is generated. if you sample at 2Hz (the recommended Nyquist rate of sampling), you get zero at zero, zero at .5, and zero at 1. what should be done to make sure you capture the signal appropriately? how would you capture a 1hz signal in the real world scenario? is this a failure of the nyquist theorem?
Given taple 3,please solve for part(d)-part(f) hange the mode on the signal generator to sine-wave, with a peak-to-peak amplitude of eak-to-peak amplitude of the voltage across the capacitor for various frequencies (100, 4 500, 2000, and 5000 Hz), and complete Table 3, (0.4%) Table 3 Frequency (in Hertz) 100 400 800 1000 1500 2000 5000 Vc (peak-to-peak) ange the mode on the signal generator to sine-wave, with a peak-to-peak amplitude of 2V. Measure the 1500, 2000, and 5000 Hz), and...
given table 4 and nowing tau was measured(0.15ms) please solve for part d,e,f Thanks hange the mode on the signal generator to sine-wave, with a peak-to-peak amplitude of 2 eak-to-peak amplitude of the voltage across the resistor for various frequencies (100, 400 500, 2000, and 5000 Hz), and complete Table 4, (04%) Table 4 Frequency (in Hertz) 100 400 800 1000 1500 2000 50 VR (peak-to-peak) (d) From Table 4, sketch the frequency response curve (lv versus frequency) of the...
Part I: Black Box A Design your first black box adhering to the following specifications A. Input Signal to Black Box A 1. A 1 kHz cosine wave with amplitude of 1V. B. Output Signal from Black Box A 1. A 1 kHz sine wave with amplitude of Hint: Use an ideal op-amp C. Explain your design process. What type of circuit did you design? Discuss D. Why did vou use an op-amp? Could another component be used instead? Why...
Settings for the 5.2A function generator: • AC Sine Wave • f = 30 Hz • Phase Shift = 50° • Offset = 0 V • Amplitude = 2 V B. Simulate the circuit seen in Figure 5.2. Use the same function generator settings as 5.2A. Record three to four cycles of both the input and output. Using the cursors on the oscilloscope, measuring the time shift between the maxima of the two waves, Δ, and use it to calculate...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform and convert it to a “regulated “dc value giving 12 volts +, - 1 volt across a 2000-ohm output load resistor with no more than 2% ripple voltage. You may assume: a. An ideal power transformer as discussed in class. b. For hand computations, you must assume a diode given by Figure 4.8 page 185. c. A filter capacitor sized per the textbook equation...
Need Table F and how you do the calculations I. EXPERIMENT 1.10: STANDING WAVES ON STRINGS A. Abstract Waves on a string under tension and fixed at both ends result in well-defined modes of vibration with a spectrum of frequencies given by the formula below B. Formulas fn=n (*), n= 1, 2, 3,... v= T where fr is the frequency of the nth standing wave mode on the string of length L, linear mass density y, and under tension T,...
Vout should be a sinusoid signal of 12Vp-p Dc voltage to uA741 : +/-8.5V Please simulate as well please help, im completely lost on this this is all of the information Experiment 5. RC Sinusoidal Oscillators PURPOSE: This laboratory provides an introduction to the background, analysis and design of sinusoidal oscillators using RC feedback networks and active devices to achieve the criteria for continuous oscillations to occur. EQUIPMENT REQUIRED : 1 Operational amplifier u.A741 1 CEU development station Resistors and...