y(t) and Y(f) correctly draw.. The low frequency signal m(t) is modulated to the dsb-sc signal y(t) using the ca...
Problem A DSB-SC AM signal is modulated by the signal m(t) = cos(4000st) - cos(1000nt). The modulated signal is u(t) = 200 m(t) cos(21tfct), where f=1 MHz. 1. Determine and sketch the spectrum of the AM signal. 2. Determine the average power in the frequency components 3. Find a resonable choice of R and C to design an envelope detector for this DSB-SC AM signal.
When the message signal m (t) =cos (2π fmt) and the
carrier signal is c(t)=cos (2π fct) ,
fm<< fc,
The modulated DSB-SC signal
SDSB-SC=m(t)cos(2πfct) is generated, and only
the upper sideband
To generate and transmit the SSB signal. As shown in the figure
below, the receiver is a local oscillator
cosine signal to the received signal and passes it through a
low-pass filter. Answer the following questions.
(a) Draw the waveform of DSB-SC modulated signal
SDSB-SC(t)
(b)Find the result...
[15 points] You are asked to design a DSB-SC AM modulator to generate a modulated signal km(t)cos(wt+0), where m(t) is a signal band-limited to B Hz. The following figure shows a DSB- SC AM modulator available in the stockroom. The carrier generator available generates not cos(wct), but cos (wct). Explain whether you would be able to generate the desired signal using only this equipment. You may use any kind of filter you like. 3. What kind of filter is required...
In a coherent detection process, a sinusoidally modulated DSB-SC wave, s(t) = c(t)m(t) where the carrier wave is c(t) =Accos(2πfct) and the message signal is m(t) = Amcos(2πfmt), is applied to a product modulator using a locally generated sinusoid of Ac’ amplitude and is out of phase by φ with respect to the sinusoidal carrier used in the modulation. (a) Draw the block diagram of the coherent detection process and label the block diagram with the information provided above accordingly....
4. A DSB-SC signal is modulated by m(t) = 7coswyt + 3coswqt, with f1 = 0.2 kHz, and Ac = 5. (25 points) a. Write an expression for the DSB-SC signal and sketch a picture of this wave. b. Evaluate and sketch the spectrum for this DSB-SC signal. C. Find the value of the normalized average power. d. Find the value of the normalized PEP.
In a DSB-SC system, the carrier is c(t) = 2A sin (2πfct) and the message signal is given by m(t) = 2sinc(8t) + 4sinc^2 (8t). What is the frequency-domain representation and the bandwidth of the modulated signal?
In a DSB-SC amplitude modulation system, the message signal is m(t)=e^(-3t)*u(t-2) and the carrier signal is ???( 2000??). Find the Fourier transform of the modulated signal.
The message signal m(t) = 2 cos 400t + 3 sin(800t + 22) modulates the carrier signal e(t) A cos(700π) using DSB-SC (dual side band, suppressed carrier) modulations Find the time domain and frequency domain representation of the modulated signal and plot the spectrum (Fourier transform) of the modulated signal. What is power content of the modulated signal?
A message signal m(t) = sin30nt +3cos200nt is to be modulated by the carrier, 1. cos(20,000nt). (a) Find X(f) (b) Find the DSB-SC signal x(t) and Xf). (c) Sketch the spectrums of |M(G| and |X(f)|. In the spectrum, identify the USB and LSB spectra. (d) Find the message signal power, m2(t). (e) Find the transmitted power, Sr x2(t). (f Find the massage signal bandwidth, B, and the transmitted signal bandwidth, Br. (g) Describe the demodulation process and find the detected...
1. DSC-SC Modulation. Consider a message signal m(t) = 3 sinc(10t) this is applied to a product modulator with a carrier wave c(t) = 2 cos(100nt). (a) (5 points) Find and plot the Fourier transform S(f) of the DSB-SC modulated signal s(t). (b) (5 points) What is the bandwidth of s(t)? (c) (5 points) The signal s(t) is next applied to filter h(t), the output of the filter is named y(t). Now assume that I $2/300, If|< 30, H(f) =...