The heat question and would like to have work solution. The answers are (c) 136.6 (d) < 2%. thank you.
The heat question and would like to have work solution. The answers are (c) 136.6 (d)...
For such aircraft application (Figure 3), a wall is made from insulation material (k-0.030 W/m.K) and the insulation material is mounted between four layers of carbon steel (2 mm thickness), the carbon layers are separated by a 2 mm air gap (kair-0.025 W/mK). Figure 3, the thermal conductivity of the carbon steel is (k-15.5 W/m.K). The temperature inside the wall is maintained at 6 °C. The environmental temperature is 24°C. The engineer would like to avoid condensation occurring at outer...
1. Heat transfer analysis of a special-purpose panel is to be performed. The temperatures at the inner and outer surfaces of the panel measure 30°C and 22°C, respectively. The dimension of the panel is 2.9 m wide, 1.3 m high and 0.40 cm thick. Its thermal conductivity is 0.13 W/m·°C. Heat is lost from the outer surface by convection and radiation. The convective heat transfer coefficient is 23 W/m2 ·°C and an ambient temperature measures 13°C. Determine (a) the fraction...
Superheated steam flows steadily through steel tubing (k 35 W/m-K) applying a tube inner surface temperature of 575°C. The tubing has an inner diameter of 300 mm and a wall thickness of 30 mm. Insulation (k 0.10 W/m-K) is applied to the outer surface of the tube while thin aluminum sheet is applied around the insulation as a protective covering. The ambient air at 27°C provides a convection coefficient of 6 W/m2-K. Determine the minimum insulation thickness necessary (mm) to...
B Steam flows in a steel pipe, which is insulated by gypsum plaster. The inner and outer diameter of the pipe are 8 cm and 6 cm respectively with pipe length of 20-m. The thickness of gypsum plaster which wraps the pipe is 4 cm. The heat transfer coefficient of the inner pipe and outer insulation are 800 W/m2.°C and 200 W/m2.°C with inner pipe temperature of 200°C and outer insulator temperature of 10°C. The thermal conductivity of the pipe...
art II- Show your work 17 Marks team at 320°C flows in a stainless steel pipe (kr 15 W/m "C) whose inner and outer diameters are 5 em and 5.5 cm, respectively. The pipe is covered with 3-cm-thick glass wool insulation (k 0.038 W m·°C). Heat is lost to the surroundings at 5°C by natural convection and radiation, with a combined natural convection and radiation heat transfer coefficient of hi-15 w/m.。C. The convective heat transfer coefficient inside the pipe to...
QUESTION 1 (10 marks) a) Write the Newton's law of heat convection in fluid using convection heat transfer coefficient, h (Wm2.K). Please explain the equation in terms of its driving force and resistancC (2 marks) (POUCOI/C2) b) Define the heat transfer rate, q,by inside and outside convection and wall conduction considering a stainless steel cylindrical pipe (inside radius, ri and outer radius, ) with fiberglass insulator (radius, s) in ą steady state condition as shown in Figure Q11 Steam with...
Consider the following composite wall of a building. It is made out of plaster board (Lp 0.85 W/mK), glass fibre insulation (Lb-160 mm, k = 0.050 W/mK) and plywood (1,-40 m m, k = 0.70 W/mK) as shown below. On a certain day, the convective heat transfer coefficients inside and outside of the building are 35 W/m2K and 65 W/m2 K respectively. The inside and outside temperatures are 24°C and 36°C respectively. The wall has a total surface area of...
a) what is the heat loss per unit length from the pipe in W/m? b) Estimate the heat loss per unit length if a 50 mm thick layer of insulation with a conductivity of 0.058 W/m K. Neglect radiation for this part. 3. A 0.20-m diameter, thin-walled steel pipe is used to transport saturated steam at a temperature of 486K in a room for which the air temperature is 25°C and convection heat transfer coefficient at the outer surface of...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C and 100°C, respectively. Determine the rate of heal transfer by radiation between the plates in Wim and the radiative heat transfer coefficient in W/m K ) 12 Write down the one-dimensional sent heal conduction equation for a plane wall with constant thermal conductivity and heat generation in its simplest form, and indicate what each variable represents 13 Write down the one-dimensional transient heat conduction...
Heat Transfer -A wall 20 cm thick is to be constructed from material that has an average thermal conductivity of 2 W/m C. The wall is to be insulated with 5cm material having an average thermal conductivity of 0.5W/m C. Assuming that the inner and outer surface temperatures of the insulated wall are 200 and 20°C, calculate the heat transfer per unit area and the intermediate Temperature between the insulation and the wall.