A beam having a T-Section is loaded as shown in figure below.

Question

Question

a. Draw the Shear Force & Bending Moment Diagram

b. Locate the Nuetral Axis

c. Find the maximum tensile and compressive bending stress

d. Find the maximum shear stress e Find the Bending Stress and Shear Stress at the points marked on the cross section

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

A beam whose cross-section is shown in the figure is subjected to a bending moment M...

A beam whose cross-section is shown in the figure is subjected to a bending moment M inclined at 0 = 70° from the z axis. a) Locate the orientation of the neutral axis B and draw this axis on the figure b) Calculate the maximum flexural tensile stress Omax,T and the maximum flexural compressive stress Omax.c in the beam and indicate at which points in the section these occur. M= 2 Nm D e Z 20 mm A B 60...
Problem 1 For the loaded beam with the cross-section shown: A. Find the location of the neutral a...

Problem 1 For the loaded beam with the cross-section shown: A. Find the location of the neutral axis B. Compute the moment of inertia of the section around the neutral axis C. Locate the section of maximum moment then compute the maximum stress due to bending, fb D. Locate the section of maximum shear-compute the shear stress at the neutral axis 3.0 k 8" 1.5 k/ft 1.0 k/ft 2" 8 10 ft 6 ft 4 ft 2" Cross-Section Problem 1...
The 25 foot beam is loaded as shown below. a. (10 points) Draw the shear and...

The 25 foot beam is loaded as shown below. a. (10 points) Draw the shear and bending moment diagrams for this beam. b. (15 points) What is the value of the maximum normal tensile and compressive stress in the beam? C. (10 points) What is the value of the maximum shear stress in the beam? 2 kips 3 kips w = 1 kip/ft VE VE 10 ft 5 ft 5 ft 5 ft 20 Beam Cross-Section

4. A cantilever beam is loaded as shown in the figure. Using the method of sections...

4. A cantilever beam is loaded as shown in the figure. Using the method of sections or the integration method, draw the shear force diagram and the bending moment diagram. If the beam cross-section is a 9 inch square, find the maximum bending stress 1200 lb 800 lb/ft 9" B 9" A Beam cross-section 8 ft 8 ft
Problem 1: Draw the shear force and bending moment diagram for the beam shown below. (10)...

Problem 1: Draw the shear force and bending moment diagram for the beam shown below. (10) Estimate the maximum bending stress located at section C (shown below). (10) Clearly identify the location on the cross section where the maximum bending stress is located. Is it tensile or compressive? Explain your answer.
The simply-supported beam having I-beam cross-section as shown in figure is to carry a uniformly distributed...

The simply-supported beam having I-beam cross-section as shown in figure is to carry a uniformly distributed load over its entire 1.2m length. Specify the maximum allowable load if the beam is made from malleable iron, ASTM A220, class 80002. The allowable tensile stress is 164 MPa and allowable compressive stress is 412 MPa. The centroid of the section is located at 35 mm from the bottom and moment of inertia are Ix = 2.66 x 10 mm". (a) Draw loading...

For the beam shown below (neglect self-weight of the beam) 16 kN x 8 mm 19...

For the beam shown below (neglect self-weight of the beam) 16 kN x 8 mm 19 kN 10 kN/m T 2 mm mm A4n - 3 m +3m → a. Draw the shear force and bending moment diagram. 2 mm Section X-X b. For the cross section x-x given, calculate the maximum tensile and compressive bending stress c. For the cross section X-X given, calculate the maximum shear stress
I-beam loaded as a cantilever beam 2. An I-beam is loaded as a cantilever beam as shown below. The cross-section of the...

I-beam loaded as a cantilever beam 2. An I-beam is loaded as a cantilever beam as shown below. The cross-section of the beam is also shown. Indicate on both illustrations, by circling and labeling, the location of the maximum tensile stress and the maximum compressive stress. 2. An I-beam is loaded as a cantilever beam as shown below. The cross-section of the beam is also shown. Indicate on both illustrations, by circling and labeling, the location of the maximum tensile...
The beam is loaded as shown in the diagram below. The beam is uniformly loaded at...

The beam is loaded as shown in the diagram below. The beam is uniformly loaded at 3 kN/m for the length of 4 m from B. The beam also has two point loads, 4 KN at 2 m from A and 3 KN at 3 m from B. 2 KN 3 KN 3KN/m A 2 m 2 m 11 m 3 m Fig. Q2 Draw a shear force and bending moment diagram. Also determine the location of maximum bending moment...

(a) Sketch the shear force and bending moment diagram for the beam shown. Indicate the values and locations of maximum shear and moment.

(a) Sketch the shear force and bending moment diagram for the beam shown. Indicate the values and locations of maximum shear and moment. (b) With the beam cross section shown, determine the maximum tensile stress, maximum compressive stress, and maximum transverse shear stress in the beam.