4 (30 pts): Synchronous 3-digit counters based on T flip-flops Write down the input logic functions...
Required to construct counters using synchronous sequential logic. Use one hex digit to display the result. ONLY AND/OR/NOT/XOR gates and flip flops allowed.BCD counters count from 0 to 9. LOGISIM - not code 1. A 4-bit binary BCD counter with T flip flops WITH enable if possible please use Logisim to build it and answer with picture of how its made.
Required to construct counters using synchronous sequential logic. Use one hex digit to display the result. ONLY AND/OR/NOT/XOR gates and flip flops allowed.BCD counters count from 0 to 9. LOGISIM - not code 1. A 3-bit binary counter with 3 JK flip flops WITH enable if possible please use Logisim to build it and answer with picture of how its made Thank you!
the design for a 3-bit synchronous down counter built with T flip- ive-high input H; when H is high the count holds, points) Draw flops. Include a synchronous, act otherwise the circuit counts down. T Q T Q T Q
(a) Design an asynchronous Binary Coded Decimal (BCD) count-up counter using JK flip-flops. Draw the counter circuit clearly showing the configuration of the JK flip-flops and the necessary logic gate(s). Sketch the input and output waveforms of this counter (7 Marks) (b) The binary up/down counter for a cargo lift controller in a 7-storey building has an up-down (UID) control input and a buzzer output (B). The buzzer will sound B 1) when the lift is at level 1 or...
Need a schematic for a 4 bit synchronous up/down counter using two JK flip flops (74112) with the program Quartus II. I am using version 14.1. There should be a preset, clear, and clock input. Four outputs. Please complete the schematic and take a screenshot for me. Has to successfully pass compilation, thank you!
3. Construct a modulo-5 parallel (synchronous) down counter using master-slave T flip- flops. The counter should count in the sequence 0-4-3-2-1-0 and then back to 4, counting continuously. The counter stages are x,y and z, where z is the most significant bit. The Qoutputs are Qx, Qy and Qu. The T-inputs of the three stages are Tx, Ty and Tz. Use Karnaugh map method (truth table for Tinputs followed by K-map) to determine each of the T-inputs (not the short-cut...
7. JK flip-flops are often used to build counters. The JK flip-flop will toggle the original output value when triggered by the clock signal if both the J.K inputs are connected with a constant "high"(logic 1). Suppose all the JK flip-flops in following Figure are positive edge triggered. The edges of the CLOCK are marked out in the figure. All the Qs have initial value 0. HIGH IFE CLOCK-HCL LK 000 0 0 0 Figure. Counter (a) Sketch the output...
Design a two-bit up/down binary counter using D flip-flops that can count in binary from 0 to 7. When the control input x is 0, the circuit counts down, and when it is 1, the circuit counts up. (a) Obtain the state table of the two-bit counter. (b) Obtain the state diagram (c) Draw the logic diagram of the circuit.
1. Design a synchronous 2-bit up-down counter using a T flip flop for the most significant bit and an SR flip flop for the least significant bit; when the input X-1, it should count down and for X-0, it should count up. Use SOP. 1. Design a synchronous 2-bit up-down counter using a T flip flop for the most significant bit and an SR flip flop for the least significant bit; when the input X-1, it should count down and...
Design a synchronous counter that counts up 0, 1, 2, 3, 0, 1, 2, 3, ... when an input x = 1, and down when x = 0 using (a) D flip-flops. (b) J-K flip-flops. You need to show the state definition table, the state transition diagram, the state transition table, the K-maps for the respective logic functions and the schematic of the implementation using flipflops and logic gates in (a) as well as the K-maps for the logic functions...