2. Give a DAC0800, and LM741, design a DAC test circuit. The
input of the circuit is eight bit number between 00H and FFH,
and the output is analog voltage ranging from -10v to 10v.
Make a table showing analog voltages for digital numbers:
00H, 08H, 80H, 88H, and FFH
Thanks so much in advance!
2. Give a DAC0800, and LM741, design a DAC test circuit. The input of the circuit...
plz give correct answer Q5. We are collecting an analog signal ranging from oV to SV with a 3-bit analog-to-digital converter. Calculate the discrete voltage range and fill in the table, and calculate the analog quantization size (resolution). 0.5pt Output states Diserete voltage range IV Analog quantization size (resolution)- 06. Calculate the resolutions for the 2-bit, S-bit, 12-bit, and 16-bit analog-digital converter: Input and output signal ranges from-10V to 10V. 0.5pt 1) 2-bit: 2) 8-bit: 3) 12-bit: 4) 16-bit:
plz do not answer it , if you do not know how to use pspice 3. Refer to Fig. 1 in the handout; obtain the circuit output in PSpice for some of the digital input combinations given in Table. 1. Assume that 5V analog input and 0V analog input correspond to a digital ‘1' and a digital .0', respectively, and that the DAC outputs are converted so that positive voltages are obtained. Also, a. What is the range, precision and...
You need to design for-bit R-2R network digital to analog converter using S k? and io with reference voltage 16 volt. i) Sketch a circuit of this digital to analog converter. i) Calculate the output voltage for an input of 1010, 1101 and 0110 Calculate output voltage resolution
Problem I (Codes, 6 Pts) Design a circuit that takes as input an ASCII-coded symbol (7 bits) and generates it parity bit. Consider for this problem the even parity. Problem II (Codes, 5 Pts) Consider a heat monitoring system containing an internal temperature sensor that produces different levels of voltage depending on the ambient temperature. The following table summarizes the possible voltage outputs: Temperature Decreasing 2.7V 3.0 v 3.3 V 3.6V 3.9 V 4.2 v 4.5 V Temperature increasing We...
Data Converters and Timing Circuits (20 marks) (a) For the timing circuit shown below, use a 1000pF capacitor and find the values of RA and RB that result in an oscillation frequency of 100KHz and a duty cycle of 75% Reset 0.693 R,+2R,)C Discharge Outpat Threshold Trigger Ground Duty-Cle2R R,+2R, ar (b) The 4-Bit Weighted-Resistor DAC Converter shown below is to be expanded into an 8-bit device a. What are the required values of the additional resistors to be added?...
A seven segment decoder is a digital circuit that displays an input value 0 through 9 as a digital output in the 7-segment display. The behavior of this design can be modeled with the schematic diagram below, where DCBA is the 4-bit input (D is the most significant bit and A is the least significant bit) and abcdefg is the 7-segment output. 2. (20 POINTS) A seven segment decoder is a digital circuit that displays an input value 0 through...
need help for d,e,f OP-Amp Circuit R-20k Fig 1 1. Design an operational amplifier circuit using an LM741 op-amp and a 10k the diagram shown in Fig 1 to produce the output voltage feedback resistor that represents Clearly write your ID number in Table 1 Table 1 Your ID Number 3775。73 . Set up the roquired gain numbers as follows and write them in Table 2 Ai- the last digit of your ID number+5 A2-the 2ed last digit of your...
An engineer wants to design a circuit that has the following input/output voltage characteristics. The variable input DC voltage source that the engineer uses has 0.5 kOhm internal resistance; in the laboratory various diodes (pn and Zener), resistors and various fixed DC voltages are available. The diodes cannot be assumed as "ideal" in the design. Sketch your circuit, show all your calculations, mathematical validations and give specifications of your selected circuit elements with their values [40]. Vout (V) 3 2...
Oil estion 2 (9%) The voltage output from a J-type thermocouple referenced 0°C is to be used to measure temperatures from 50 to 70°C. The output voltages vary linearly over this range from 2.585 to 3.649 mV 1. If the thermocouple voltage is input to a 12-bit A/D converter having a +5V range, estimate the percent quantization error in the digital value; 2. If the analog signal can be first passed through an amplifier circuit, compute the amplifier gain required...
2. Design a non-inverting op-amp circuit with two resistors under the following conditions: a. The gain of the amplifier must be +10 b. The input range is ± 2V c. The total power consumed by the resistors must be less than 100 mW Show all the calculations required to design the amplifier circuit with the shown specifications.in details Use MULTISIM to create the op-amp circuit and print a fully labelled diagram of the circuits with the voltmeters displays showing both...