A finite wing area of 1.5 ft2 and aspect ratio of 6 is tested in a...
A finite wing area of 1.5 ft2 and aspect ratio of 6 is tested in a subsonic wind tunnel at a velocity of 180 ft/s at standard sea-level conditions. At an angle of attack of ?1°, the measured lift and drag are 0 and 0.181 lb, respectively. At an angle of attack of 2°, the lift and drag are measured as 5.0 and 0.23 lb, respectively. Calculate the span efficiency factor and the infinite-wing lift slope. (Round the final answers to four decimal places.)
The span efficiency factor, e, is .
The infinite-wing lift slope is per degree.
Homework Answers
Add Answer to:
A finite wing area of 1.5 ft2 and aspect ratio of 6 is
tested in a...
3. An airplane (weight 3,000 lb, wing span 35.5 ft, wing area 135 ft2, Oswald efficiency...
3. An airplane (weight 3,000 lb, wing span 35.5 ft, wing area 135 ft2, Oswald efficiency factor 0.85, zero-lift drag coefficient 0.05) flies with 90 kts at 8,000 ft. The asymmetrical airfoil has a lift-curve slope of 0.1 per degree, a zero-lift angle of attack of -3.0°, and a stall angle of attack of 15°. Assume a linear lift curve all the way to the stall. a. Calculate the density at the flight altitude in slug/ft? (6 points)
Q7. Consider the twin-jet airplane described as follow: wing area = 47 m2, aspect ratio =...
Q7. Consider the twin-jet airplane described as follow: wing area = 47 m2, aspect ratio = 6.5, Oswald efficiency factor = 0.87, weight = 103,047N, and zero-lift drag coefficient = 0.032. The airplane is equipped with two jet engines with 40,298 N of static thrust each at sea level. The thrust-specific fuel consumption is 1.0 N of fuel per newton of thrust per hour, the fuel capacity is 1900 gal, and the maximum gross weight is 136,960 N. Calculate the...
P2. Consider two wings with a NACA 23012 airfoil section: (a) one with an aspect ratio of 4 and (...
P2. Consider two wings with a NACA 23012 airfoil section: (a) one with an aspect ratio of 4 and (b) the other wing with an spetratio of 10. The span efficiency factor is e-0.95 for both wings. Both wings Note: the lift slope for a NACA 23012 is 0.106 per degree, and are flying at an angle of attack of 2 1.5° alculate the change in lit coefficient for both wings if the angle of attack is perturbed by an...
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt...
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt with a wing span b-1lm Assuming the wing rectangular, what is the Reynolds number at an altitude z-1,000m. A model of this airplane, scaled by a factor of 2, is tested in a wind tunnel at sea level. What should be the velocity in the wind tunnel to have dynamics similarity (neglect Mach number effects). What will be the lift measured...
80 m 845 m2 7.53 Wing Span Wing Planform Area Wing Aspect Ratio Sweep angle at...
80 m 845 m2 7.53 Wing Span Wing Planform Area Wing Aspect Ratio Sweep angle at quarter chord (0.25c) Taper ratio 33.5 0.3 A380 1500 m² Component Wetted Area Fuselage Wing 1700 m Horizontal tail Vertical tail Engines (4) 290 m² (each) 400 m² 280 m² Cruise Mach Number 0.85 Cruising Altitude 12.5 km Wing Loading 16500 N/m2) Temperature Geo potential Altitude above Sea Level -- (m) Acceleration of Gravity (m/s) Absolute Pressure -p- (104 N/m2) Density .p. (101 kg/m3)...
80 m 845 m2 7.53 Wing Span Wing Planform Area Wing Aspect Ratio Sweep angle at...
80 m 845 m2 7.53 Wing Span Wing Planform Area Wing Aspect Ratio Sweep angle at quarter chord (0.25c) Taper ratio 33.5 0.3 A380 1500 m² Component Wetted Area Fuselage Wing 1700 m Horizontal tail Vertical tail Engines (4) 290 m² (each) 400 m² 280 m² Cruise Mach Number 0.85 Cruising Altitude 12.5 km Wing Loading 16500 N/m2) Temperature Geo potential Altitude above Sea Level -- (m) Acceleration of Gravity (m/s) Absolute Pressure -p- (104 N/m2) Density .p. (101 kg/m3)...
The large airplane has a span of 50 meters, an elliptic wing of aspect ratio 6,...
The large airplane has a span of 50 meters, an elliptic wing of aspect ratio 6, a mass of 60,000 kg and is flying at sea level density (1.2 kg/m^3) at 100 m/s. Assume that it has a NACA 0009 (symmetric) airfoil, i. Calculate the actual lift coefficient for the wing ii. Calculate the geometric angle of attack. iii. What is the downwash angle? iv. What is the downwash velocity at the wing? v. What is the strength (circulation) of...
Problem 2 (20 points) The measured lift slope for a new airfoil is 0.0975 degree, with...
Problem 2 (20 points) The measured lift slope for a new airfoil is 0.0975 degree, with ac o =-1.15º. Consider a finite wing using this airfoil, with AR of 10 and taper ratio of 0.6. Calculate the lift and induced drag coefficients for this wing at a geometric angle of attack of 9º. Also, find the span efficiency factor. Hint: See Eq. (5.70) and Fig. 5.20. Are the values of lift and induced drag coefficients reasonable? Use 8 =1.
A business jet has a wing area of 88.3 square meters, an aspect ratio of 8.2,...
A business jet has a wing area of 88.3 square meters, an aspect ratio of 8.2, an Oswald efficiency factor of .89, a zero-lift drag coefficient of .026, a mass of 19,000 kg, and a maximum static thrust at sea level for each engine of 61,600 N (A) Calculate the maximum rate of climb at sea level. (B) Calculate the maximum rate of climb at an altitude of 13 km. (C) Estimate its absolute ceiling assuming the maximum rate of...
A Twin Engine Air craft has following Characters: Wing Area: 45 m² Gross Weight = 100000N...
A Twin Engine Air craft has following Characters: Wing Area: 45 m² Gross Weight = 100000N aspect ratio=7.0 span efficiency factor= 0.85 Parasit drag coefficient = 0.03 Each Jet Engine produces 4000on of Thrust at sea level airplane is taking off at full gross weight and the runway has paved surface. Given that the maximum lift coefficient during ground roll is 2.5 and the pair of wings are 2-m above the ground. At sea-level conditions, a) (10 pts) determine the...
3. An airplane (weight 3,000 lb, wing span 35.5 ft, wing area 135 ft2, Oswald efficiency factor 0.85, zero-lift drag coefficient 0.05) flies with 90 kts at 8,000 ft. The asymmetrical airfoil has a lift-curve slope of 0.1 per degree, a zero-lift angle of attack of -3.0°, and a stall angle of attack of 15°. Assume a linear lift curve all the way to the stall. a. Calculate the density at the flight altitude in slug/ft? (6 points)
Q7. Consider the twin-jet airplane described as follow: wing area = 47 m2, aspect ratio = 6.5, Oswald efficiency factor = 0.87, weight = 103,047N, and zero-lift drag coefficient = 0.032. The airplane is equipped with two jet engines with 40,298 N of static thrust each at sea level. The thrust-specific fuel consumption is 1.0 N of fuel per newton of thrust per hour, the fuel capacity is 1900 gal, and the maximum gross weight is 136,960 N. Calculate the...
P2. Consider two wings with a NACA 23012 airfoil section: (a) one with an aspect ratio of 4 and (b) the other wing with an spetratio of 10. The span efficiency factor is e-0.95 for both wings. Both wings Note: the lift slope for a NACA 23012 is 0.106 per degree, and are flying at an angle of attack of 2 1.5° alculate the change in lit coefficient for both wings if the angle of attack is perturbed by an...
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt with a wing span b-1lm Assuming the wing rectangular, what is the Reynolds number at an altitude z-1,000m. A model of this airplane, scaled by a factor of 2, is tested in a wind tunnel at sea level. What should be the velocity in the wind tunnel to have dynamics similarity (neglect Mach number effects). What will be the lift measured...
80 m 845 m2 7.53 Wing Span Wing Planform Area Wing Aspect Ratio Sweep angle at quarter chord (0.25c) Taper ratio 33.5 0.3 A380 1500 m² Component Wetted Area Fuselage Wing 1700 m Horizontal tail Vertical tail Engines (4) 290 m² (each) 400 m² 280 m² Cruise Mach Number 0.85 Cruising Altitude 12.5 km Wing Loading 16500 N/m2) Temperature Geo potential Altitude above Sea Level -- (m) Acceleration of Gravity (m/s) Absolute Pressure -p- (104 N/m2) Density .p. (101 kg/m3)...
80 m 845 m2 7.53 Wing Span Wing Planform Area Wing Aspect Ratio Sweep angle at quarter chord (0.25c) Taper ratio 33.5 0.3 A380 1500 m² Component Wetted Area Fuselage Wing 1700 m Horizontal tail Vertical tail Engines (4) 290 m² (each) 400 m² 280 m² Cruise Mach Number 0.85 Cruising Altitude 12.5 km Wing Loading 16500 N/m2) Temperature Geo potential Altitude above Sea Level -- (m) Acceleration of Gravity (m/s) Absolute Pressure -p- (104 N/m2) Density .p. (101 kg/m3)...
The large airplane has a span of 50 meters, an elliptic wing of aspect ratio 6, a mass of 60,000 kg and is flying at sea level density (1.2 kg/m^3) at 100 m/s. Assume that it has a NACA 0009 (symmetric) airfoil, i. Calculate the actual lift coefficient for the wing ii. Calculate the geometric angle of attack. iii. What is the downwash angle? iv. What is the downwash velocity at the wing? v. What is the strength (circulation) of...
Problem 2 (20 points) The measured lift slope for a new airfoil is 0.0975 degree, with ac o =-1.15º. Consider a finite wing using this airfoil, with AR of 10 and taper ratio of 0.6. Calculate the lift and induced drag coefficients for this wing at a geometric angle of attack of 9º. Also, find the span efficiency factor. Hint: See Eq. (5.70) and Fig. 5.20. Are the values of lift and induced drag coefficients reasonable? Use 8 =1.
A Twin Engine Air craft has following Characters: Wing Area: 45 m² Gross Weight = 100000N aspect ratio=7.0 span efficiency factor= 0.85 Parasit drag coefficient = 0.03 Each Jet Engine produces 4000on of Thrust at sea level airplane is taking off at full gross weight and the runway has paved surface. Given that the maximum lift coefficient during ground roll is 2.5 and the pair of wings are 2-m above the ground. At sea-level conditions, a) (10 pts) determine the...
Most questions answered within 3 hours.
-
A generator has a
450-turn coil that is 10 cm long and 12 cm wide. The...
asked 5 minutes ago -
Can someone please explain how you get the calculations for the
shear and moment diagrams with...
asked 5 minutes ago -
- Describe the process of planning, managing, and controlling
quality in projects.
Class - A project...
asked 7 minutes ago -
1.) In order to appreciably influence the vapor pressure of a
liquid mixture a substance must...
asked 13 minutes ago -
Chapter 05, Problem 01
A car travels at a constant speed around a circular track
whose...
asked 14 minutes ago -
Which of the following quotes from a new-product adopter would
signal the need for a firm...
asked 35 minutes ago -
Why are anthropologists interested in studying exchange across
cultures?
asked 29 minutes ago -
3. You may be aware that Wal-Mart is also using RFID
technologies at their stores. Name...
asked 35 minutes ago -
What are the key benefits and limitations of a relational
DBMS?
asked 39 minutes ago -
A medium-sized carrot weighs 64 g and contains 7.0 g of
carbohydrate.
What percent, by mass,...
asked 41 minutes ago -
Please design 3 different and unique brackets consisting of TOP,
FRONT, RIGHT or LEFT views with...
asked 57 minutes ago -
La Niña conditions are forecasted to result in dry conditions in
the spring. You are trying...
asked 1 hour ago