2.24
A pipe of 0.3 m outer diameter at a temperature of 160°C is insulated with a material having a thermal conductivity of k = 0.055 (1 + 2.8 × 10–3T) W/mK where T is in °C. The outside surface temperature is 40°C. Determine the heat flow/m length and the temperature at the mid radius
2.24 A pipe of 0.3 m outer diameter at a temperature of 160°C is insulated with...
Exercise 1.16 An insulated district heating pipe with a total diameter d = 0.4 m is laid in the ground at a depth of h = 1.2 m. For a long cold period with an average ground surface temperature of 0°C and a temperature at the outer edge of the pipe insulation of 20°C, the heat loss per 1km of steam pipe must be calculated. The thermal conductivity of the soil should be assumed to be 0.6 W/mk Exercise 1.16...
A cylinder of diameter 0.6 m and length of 15 m with surface temperature of 200 Celsius is enclosed in a square of 1.2 m side, the material having a thermal conductivity of 2.5 W/mk. the outside surface at 5 Celsius . Determine the heat loss in W
5.10. A pipe carrying steam at 250°C with and OD of 0.2 m is insulated using a material with conductivity of 0.085 W/mK. The insulation is off-set from the axis by 0.05 m and the OD of the insulation is 0.4 m. Determine the heat loss from the pipe if the outside surface temperature of the insulation is 60°C.
B Steam flows in a steel pipe, which is insulated by gypsum plaster. The inner and outer diameter of the pipe are 8 cm and 6 cm respectively with pipe length of 20-m. The thickness of gypsum plaster which wraps the pipe is 4 cm. The heat transfer coefficient of the inner pipe and outer insulation are 800 W/m2.°C and 200 W/m2.°C with inner pipe temperature of 200°C and outer insulator temperature of 10°C. The thermal conductivity of the pipe...
6 Water is heated in a pipe by exchanging heat with a warmer fluid that flows outside the pipe. Inside diameter of the pipe is dn 0.045 m and outside diameter dour0.05 m. Mean velocity of the water in the pipe is um-0.31 m/s and the bulk temperature is 323 K (density 988 kg m-3; viscosity 0.00055 kg m' sı. Pr 3.56, thermal conductivity k 0.64 W m1 Kt). The material of the pipe has thermal conductivity k 0.61 W...
Problem : A cryogenic flui d is flowing in a 304 SS pipe. The pipe is insulated on its outside surface with 6 - mm thick, evacuated, aluminum foil/glass mat insulation. (“Evacuated” means a partial vacuum is drawn on the insulation to remove air that would otherwise fill pores inside the insulation.) The pipe inside diameter is 127 mm; it’s outside diameter is 138 mm. The fluid temperature is - 173 o C . T he air temperature outside the...
4. (25 pts) Water is flowing inside a thin wall, smooth pipe of diameter 0.05 m at a mass flowrate of 0.3 kg/s. The water enters the pipe at a mean temperature Tm,i= 80 °C and exits at Tm,o= 80 °C while the pipe surface temperature is maintained at Ts= 20 °C along its entire length. a. Is the flow turbulent or laminar? b. Calculate the average convection heat transfer coefficient inside the tube. c. Calculate the length of the...
Problem 1. Steam at 120°C is transported in a long 8" outer diameter pipe. Its outer surface is covered with a 1" thick fiberglass (thermal conductivity, 0.05 W/(mK)) insulation. When the outer temperature is 0°C, the rate of condensation of steam is measured to equal 0.06 g per meter of the pipe length. Estimate the heat transfer coefficient. The heat of vaporization of the steam is 2600 J/g. The resistance to the heat transfer through the pipe wall may be...
A pipe with insulation material is used to carry steam to an operating plant. The conditions and dimensions for the system are as follows Variable Value Length of pipe, L 100 ft Inner diameter of pipe, Do 1 inch Outer diameter of pipe, D1 1.24 inches Outer diameter of insulation, D2 2 inches Inside film heat transfer coefficient for condensing saturated steam, ho 800 Btu/hr-ft2.oF Outside film heat transfer coefficient for air, ht 2 Btu/hr-ft2.oF Thermal conductivity of the pipe,...
A long cylindrical rod of diameter 100 mm with thermal conductivity of 0.5 W/mK experiences uniform volumetric heat generation of 5.0 x 10 W/m². The rod is encapsulated by a circular sleeve having an outer diameter of 400 mm and a thermal conductivity of 4 W/mK. The outer surface of the sleeve is exposed to cross flow of air at 27°C with a convection coefficient of 25 W/m2K (a) Find the temperature at the Interface between the rod and sleeve...