Pt 1 Please find voltage and power across RLoad for both 100 ohms and 220 ohms....
A. Calculate Vout for both circuits by hand and include your calculations in your Pre-Lab B. Build the circuits in LTSpice and attach a 10K ohm termination resistor across Vout for both the Thevenin and Norton Source circuits and simulate to find the output voltages. C. What is the formula for Vout as a function of Vsource, Isource, Rload, Rs? D. Calculate Vout by hand when there is no load resistance (Rload = infinity) and again with Rload = 5K....
IN OUT LM317 R1 Ci ADJ 240V 121 0.1u LOAD Vac 50Hz R2 Bridge Rectifier Let Ci = 2200uF, R LOAD = 100, R1-120, R2-820 Calculate the output voltage of the power supply (acrosS RLOAD), in Volts. [Do not enter units in your answer.] Answer: By considering this circuitincluding a zener diode, and by determining the minimum and maximum currents associated with the zener, calculate a maximum value for R. Assuming the units are in ohms, provide only the numerical...
Problem 3: (20 points) A zener-diode voltage regulator circuit is shown belkw zener diode has breakdown voltage Vz 8.0V and the zener resistance is nsumed to be 0 ohms. The power supply voltage Vps can vary between 10V and 14V and the lod resistance Ri can vary between 100 ohms and 1 kohm, 圧 1. Find a value of R such that the zener diode remains properly biased over the range of variation of Vps and RI (hint: the minimum...
EE 282-Circuit I Pre-Lab 9 Maximum Power Transfer Theorem Name Concepts: In this pre-lab we will be leaming about Maximum Power Transfer Theorem. Maximum power is transferred to the load when the load resistance equals the thexenin equivalent, and we carry out the analysis using Thevenin's equivalent circuit. In order to do this, first build the following circuit on Mutism. 1 R1 5.1k0 R3 2 V1 R2 8kQ 6.8㏀ Fig. 1 Part 1: To find the Thevenin equivalent resistance, we...
5.29 A power supply is an instrument or circuit that produces a steady voltage similar to a battery. A good power supply produces an almost constant voltage and has almost zero Thevenin resistance. In the power supply of Fig. 5-28a there is an adjustment for changing the output voltage from 10 to 30 V. This being the case, what is the minimum load power with a 100-0 load? The maximum load power? 5.30 What current rate should the fuse of...
1. In class we derived how a transformer can up or downregulate the voltage in an electrical circuit with an alternating current. (a) Use the conservation of energy to deduce how the currents I1 and I2 must be related if you know the ratio of ε1/ε2 (for the purpose of calculating the power delivered by a circuit ignore any complications due to the fact that I(t) and ε(t) are time-varying). (b) In class I argued that power transmission is more...
Q1. (3 marks) In the circuit shown below, R-1.5KO and the voltage drop across Ri is 4.5V. (1 pt.) A. What is the voltage drop across R? (1 pt.) B. What is the value of the resistance R? (1 pt.) C. What is the power delivered by the source voltage? S Answer: wwiw R Ri Vs=15V Q2. (3 marks) Refer to the circuit below. A. Using the voltage divider law, find the voltage between the points A and B. B....
1. (10 PT) A three-phase bridge rectifier circuit shown in the figure phase voltage of 220 volts rms. A load of 100 Ω is connected across is supplied by a rectifier. Both the primary and secondary windings of transfor Assume the transformer has a turns ratio of unity mer are Y-connected a) 3 PTI On the top of voltage plot on next page indicate the diodes that will be conducting during different intervals of time. b) 17 PT] Plot the...
Please find the voltage and power of the circled 100 Ohm resistor, and then repeat for a 220 ohm resistor, showing your work. is lon 3470 2205 Asu 109 Lun 220
*****Use R = 8 ohms********** Please answer both questions a and b. R Q 0.1 H 100 V 1 mF HE + 30%) Find the value wo .The circuit above shows a RLC series circuit that are connected LC across the voltage source 100 V rms AC. a) By hand solve: For the value of wo find voltages and currents in L,C,R, power and power factor at the source. Scan your work and upload to D2L b) For different values...