In the series LCR circuit, the L and C produce the reactance
while R has resistance. The value of resistance is constant while
values of both reactance of L and C depends on frequency
.
Thus L and C are main components in order to produce AC signals therefore they are compromise one circuit unit while R is constant value generator.
Therefore ,R is not put in between L and C for the circuit.
4. In Fig. 5, can you put R between L and C for performing Experiments 8.1...
R: 1 , 5.1
C .022 μF
L: 47 mH
WA v; () Fig. 4 - RLC circuit powered by the function generator set to a square wave The inductor voltage can be solved by first determining the circuit current, then by differentiating the current using the following equation. For the details of the RLC circuit theory please refer to the lecture notes. ve = Leate 1 = 0 on R C off VZORL Fig. 5 - Model of the...
How do you draw the phasor diagram?
L=3.3 mH
C=0.39 uF
R=100 ohms
in case you need it in order to see table 2 work
2. Based on the calculated phase angles Peneos, or Pexp in Table 2, draw a phasor diagram for each of the two frequencies: f = 1000 Hz and 8000 Hz, and complete the following two statements. (a) At f = 8000_Hz, the voltage (1) across the signal generator leads the current (i). (b) At f...
I am currently trying to figure out the experiment below. Please
complete Table 1 with an explanation, I appreciate it thank
you! Promise to give thumbs up!
Introduction The phase differences between the output voltage, the voltage across the inductor, the voltage across the capacitor, and the voltage across the resistor will be examined at resonant frequency. The voltage and phase relationship will also be examined for frequencies above and below resonance. Theory An inductor, a capacitor, and a resistor are...
Answer 4 & 5 please! thank
you!
R values =
Resistor value, R1 = 990 Ohms
Resistor value, R2 = 2050 Ohms
4. Connect the 2nd resistor in parallel with the 1st
resistor and connect that combination to the battery.
Measure
the following:
The
current passing through the R1, I1 = ___0.0058____ A
The
current passing through the R2, I2 = ___0.0031____ A
The
current supplied by the battery, I = ___0.0092____ A
Calculate I1 + I2 =...
Pease answer questions 4 and 5! Thank you so much!
4. Connect the 2nd resistor in parallel with the 1st
resistor and connect that combination to the battery.
Measure
the following:
The
current passing through the R1, I1 = ___0.0058____ A
The
current passing through the R2, I2 = ___0.0031____ A
The
current supplied by the battery, I = ___0.0092____ A
Calculate I1 + I2 = ____________ A
Is the following statement true? I = I1 +...
so completely lost, please show your work thank you :-)
heres what they wrote if it helps... "A' for effort and i
appreciate but if you could please rewrite that would be amazing!
ty
Record in Table 2 the measured values of t(v) and (U) at the three frequencies Table 2 Measured values of t(Ux) and (U) at the three frequencies (L = 3.3 mH, C = 0,39 uF, R = 100 2 ) f = 1000 Hz f =...
Course and Section cto EXPERIMENT ac series-Parallel Sinusoidal Circuits OBJECTIVES 1. Measure the currents of series-parallel R-L and R-C networks using sensing resistors 2. Demonstrate the Pythagorean relationship between the currents of the networks. 3. Measure the phase angles associated with the currents of the networks. 4. Calculate the input impedance of a parallel network using measured values EQUIPMENT REQUIRED Instruments Resistors 1-10-Q, 470-Ω, l-kM (14.W) Inductors 1-10-mH Capacitors 1-0.02-pF I-DMM 1--Oscilloscope 1-Audio oscillator or function generator 1--Frequency counter (if...
For MATLAB users. Can you please type the answers for the MATLAB
sections.
Consider the RLC circuit where R - 5, C- 1, L- 4 and Vs - 8 1. Use circuit analysis laws to show that the resistor's voltage and induc- tor's voltage can be modelled as the system of ODEs Vi VL RC 2. Solve the eigenvalues and eigenvectors of the coefficient matrix in the system of ODEs. 3. Verify your answer for question (2) by using the...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...