Homework Answers
Add Answer to:
P2:30 Kerosene at 96 C and flow rate of 20 kg/s must be cooled to 85...
Problem 2: Heat exchanger (25 points) Cold water (op 4179 J/kg K) enters the tubes of a heat exchanger at 20 °C at a rate of 3 kgs. while hot oil (cp 2200 J/kg.K) enters the shell at 130 C at the sam...
Problem 2: Heat exchanger (25 points) Cold water (op 4179 J/kg K) enters the tubes of a heat exchanger at 20 °C at a rate of 3 kgs. while hot oil (cp 2200 J/kg.K) enters the shell at 130 C at the same mass flow rate and leaves at 60°C The heat exchanger consistsoftwo shells and 20 tubes, each executing four passes (two passes per shell). If the W/m2-K, assume the tube wall is very thin with convective heat transfer...
QUESTION 4 (25 marks) Water (Cr 4.208 kJ/kg.K) at flow rate of 5.11 kg/s s heated from 78°C to 98°C in an economize...
QUESTION 4 (25 marks) Water (Cr 4.208 kJ/kg.K) at flow rate of 5.11 kg/s s heated from 78°C to 98°C in an economizer inside a boiler. The boiler is a cross flow heat exchanger with single pass, shell fluid mixed and other fluid unmixed. The average water velocity in the 1.5 cm diameter (D) tube is 1.27 m/s. On the shell side, hot air (C,-1.0341 kJ/kgK) was used as the heating fluid with 7.3 kg/s of it entering the exchanger...
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters...
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters of 10.2mm and 12.5mm and has to be cooled to 136°C. The tubes are made of steel of thermal conductivity k-40 W/m.K. Air at 10°c enters the exchanger (unfinned) with a volumetric flow rate of 1.0 m3/s. The convective heat transfer coefficient...
[20] Question 3 Crude oil is to be heated from 22 °C to 58 °C by heat exchange with the bottom product froma dis...
[20] Question 3 Crude oil is to be heated from 22 °C to 58 °C by heat exchange with the bottom product froma distillation column. The bottom product, flowing at 30 kg/s, is to be cooled from an initial temperature of 145 °C to 105 °C. The following shell and tube heat exchanger is available: 600 mm ID (1 shell pass) Shell inside diameter Tube configuration 2 passes 19.05 mm Tube outside diameter 2.1 mm Tube wall thickness 1.25 x...
Problem 2: Heat exchanger (25 points) Cold water (op 4179 J/kg K) enters the tubes of a heat exchanger at 20 °C at a rate of 3 kgs. while hot oil (cp 2200 J/kg.K) enters the shell at 130 C at the same mass flow rate and leaves at 60°C The heat exchanger consistsoftwo shells and 20 tubes, each executing four passes (two passes per shell). If the W/m2-K, assume the tube wall is very thin with convective heat transfer...
QUESTION 4 (25 marks) Water (Cr 4.208 kJ/kg.K) at flow rate of 5.11 kg/s s heated from 78°C to 98°C in an economizer inside a boiler. The boiler is a cross flow heat exchanger with single pass, shell fluid mixed and other fluid unmixed. The average water velocity in the 1.5 cm diameter (D) tube is 1.27 m/s. On the shell side, hot air (C,-1.0341 kJ/kgK) was used as the heating fluid with 7.3 kg/s of it entering the exchanger...
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters of 10.2mm and 12.5mm and has to be cooled to 136°C. The tubes are made of steel of thermal conductivity k-40 W/m.K. Air at 10°c enters the exchanger (unfinned) with a volumetric flow rate of 1.0 m3/s. The convective heat transfer coefficient...
[20] Question 3 Crude oil is to be heated from 22 °C to 58 °C by heat exchange with the bottom product froma distillation column. The bottom product, flowing at 30 kg/s, is to be cooled from an initial temperature of 145 °C to 105 °C. The following shell and tube heat exchanger is available: 600 mm ID (1 shell pass) Shell inside diameter Tube configuration 2 passes 19.05 mm Tube outside diameter 2.1 mm Tube wall thickness 1.25 x...
Most questions answered within 3 hours.
-
Design a class Holiday that represents a
holiday during the year. This class has three
private...
asked 13 minutes ago -
Problem 1 (Logistic Regression and KNN). In this problem, we
predict Direction using the data Weekly.csv....
asked 11 minutes ago -
What is the difference between VNTRs (Variable Number Tandem
Repeats) and STRs (Short Tandem Repeats) used...
asked 18 minutes ago -
Fill in
Isotope: 15 O
1. Element name:
2. Atomic number:
3. Mass number:
4. Number...
asked 17 minutes ago -
These days with the cost of a college education it is important
to be able to...
asked 25 minutes ago -
c++
Implement Radix Sort Most sorting algorithms, like bubble,
insertion, selection and shell follow similar implementations....
asked 33 minutes ago -
Many adult tissues contain terminally differentiated cells that
are incapable of proliferation. How can these tissues...
asked 34 minutes ago -
A survey of tobacco use in high schools tested the saliva of
female and male students...
asked 54 minutes ago -
Assume that the mutation rate for a given gene is
510-6 mutations per gene per generation....
asked 53 minutes ago -
The majority of innovation organizational communication has
been driven by technological advancements in the past thirty...
asked 53 minutes ago -
If one motor has three times as much power as another, then the
smaller power motor:...
asked 52 minutes ago -
Discuss at least four issues that are important to
accountants.
I need 2 pages of explanations
asked 52 minutes ago