Homework Answers
Add Answer to:
I am a student in mechanical engineering. I would like to
solve this question in the...
A pump delivers water at 200C between a reservoir and a water tank that is 75[ft] higher than the...
A pump delivers water at 200C between a reservoir and a water tank that is 75[ft] higher than the reservoir. The suction side of the system consists of a cast iron pipe of 1[ft]diameter with a strainer (Ks= 2.5) and four 90-degree bends at R/D= 5. The discharge side of the system includes a 1000[ft] long commercial steel pipe with 12” diameter followed by a gate valve. The NPSH required for the pump is 10[ft], and the design discharge is...
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4...
yes
you can
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4-in Schedule 40 steel pipe, 1500 cm long. The total length of 2-in Schedule 40 steel pipe in the discharge line is 200 m. Assume the entrance from reservoir 1 is through a square-edged inlet and that the elbows are 90° standard. The valve is fully open globe valve. A) List the piping systems components B) Generate...
please solve it step by step with details thank you!!!!! Water is to be pumped from...
please solve it step by step with details
thank you!!!!!
Water is to be pumped from one large, open tank to a second large open tank as shown in Figure 1. The pipe diameter throughout is 15 cm and the total length of the pipe between the pipe entrance and exit is 60 m. Minor loss coefficient for the entrance, exit and the elbow are shown, and the Darcy friction factor for the pipe can be assumed constant and equal...
Water at 15° is flowing at the rate of 14.4m²/hr (Fig. 2). The head added by...
Water at 15° is flowing at the rate of 14.4m²/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of ε = 5.1 x 108m. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are standard 90°....
Water (density 998 kg/mº, dynamic viscosity 0.001 Pa s) is pumped between two reservoirs at a...
Water (density 998 kg/mº, dynamic viscosity 0.001 Pa s) is pumped between two reservoirs at a volumetric flow rate of 0.006 m/s through a 120-m long pipe of 5 cm diameter. The roughness ratio of the pipe is a/d = 0.001. There are some fittings and valves in the pipe system, as shown in Figure Q1. The loss coefficients of the valves and fittings can be found in Table Q1. The Darcy friction factor can be found in the Moody...
You need to pump water at 20 C from an open reservoir at flow rate of...
You need to pump water at 20 C from an open reservoir at flow rate of 1.4 x 10^-3 m3/s through a pipe with an inside diameter of 0.03m, using a centrifugal pump having an (NPSH)aq =2.5 m and the equivalent length on the suction side is 3m. There are several minor losses: four standar 90 flanged elbows, and fully open flanged globe valve, fully open flanged gate valve, and the Entrance. What is the the maximum distance above the...
Send somit Click Submit to complete this assessment. Question 4 p 4 uestion 4 30 points...
Send somit Click Submit to complete this assessment. Question 4 p 4 uestion 4 30 points You need to pump water at 20°c from an open reservoir at flow rate of 1.4*103 m/s through a pipe with an inside diameter of 0.03 m, using a centrifugal pump having un (NPS)req - 2.5 m and the equivalent length on the suction side is 3 m. There are several minor losses: four standard 90 flanged elbows, and fully open fanged globe valve,...
A pump that is 80% efficient pumps water from the lower tank to the upper tank...
A pump that is 80% efficient pumps water from the lower tank to the upper tank at a flow rate of 0.01 m/s through 70 meters of 10-cm diameter pipe. In this system there are two regular, screwed 90 degree elbows and a fully open screwed angle valve. Assume the reservoir exits and entrances are sharp. The friction factor,f, of the pipe is 0.02. What horsepower pump is needed to achieve this flow rate? Use: Pwater = 998 kg/m2; Mwater...
Q4: The pump is used to deliver of water from a river to a storage reservoir....
Q4: The pump is used to deliver of water from a river to a storage reservoir. The four pipes are connected in series of Inverse L shape which means the first pipe in vertical direction and others in horizontal direction. The first pipe in vertical position of 500m length of 150 mm diameter cast iron pipe, the second pipe is bend at 90' with a radius of 0.75m, the third pipe in horizontal direction of 100m length of 160mm diameter...
yes
you can
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4-in Schedule 40 steel pipe, 1500 cm long. The total length of 2-in Schedule 40 steel pipe in the discharge line is 200 m. Assume the entrance from reservoir 1 is through a square-edged inlet and that the elbows are 90° standard. The valve is fully open globe valve. A) List the piping systems components B) Generate...
please solve it step by step with details
thank you!!!!!
Water is to be pumped from one large, open tank to a second large open tank as shown in Figure 1. The pipe diameter throughout is 15 cm and the total length of the pipe between the pipe entrance and exit is 60 m. Minor loss coefficient for the entrance, exit and the elbow are shown, and the Darcy friction factor for the pipe can be assumed constant and equal...
Water at 15° is flowing at the rate of 14.4m²/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of ε = 5.1 x 108m. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are standard 90°....
Water (density 998 kg/mº, dynamic viscosity 0.001 Pa s) is pumped between two reservoirs at a volumetric flow rate of 0.006 m/s through a 120-m long pipe of 5 cm diameter. The roughness ratio of the pipe is a/d = 0.001. There are some fittings and valves in the pipe system, as shown in Figure Q1. The loss coefficients of the valves and fittings can be found in Table Q1. The Darcy friction factor can be found in the Moody...
Send somit Click Submit to complete this assessment. Question 4 p 4 uestion 4 30 points You need to pump water at 20°c from an open reservoir at flow rate of 1.4*103 m/s through a pipe with an inside diameter of 0.03 m, using a centrifugal pump having un (NPS)req - 2.5 m and the equivalent length on the suction side is 3 m. There are several minor losses: four standard 90 flanged elbows, and fully open fanged globe valve,...
A pump that is 80% efficient pumps water from the lower tank to the upper tank at a flow rate of 0.01 m/s through 70 meters of 10-cm diameter pipe. In this system there are two regular, screwed 90 degree elbows and a fully open screwed angle valve. Assume the reservoir exits and entrances are sharp. The friction factor,f, of the pipe is 0.02. What horsepower pump is needed to achieve this flow rate? Use: Pwater = 998 kg/m2; Mwater...
Q4: The pump is used to deliver of water from a river to a storage reservoir. The four pipes are connected in series of Inverse L shape which means the first pipe in vertical direction and others in horizontal direction. The first pipe in vertical position of 500m length of 150 mm diameter cast iron pipe, the second pipe is bend at 90' with a radius of 0.75m, the third pipe in horizontal direction of 100m length of 160mm diameter...
Most questions answered within 3 hours.
-
Using technology to support HR activities increases:
a.
the efficiency of the administrative HR functions.
b....
asked 14 seconds from now -
1. List the features used to classify leaf
types.
2. List some characteristics that are shared...
asked 4 minutes ago -
The three elements of Value Proposition, Key Customers, and
Capabilities operate within an environment. Which of...
asked 7 minutes ago -
Katelynn, a physician, earns $200,000 from her medical practice
in the current year. She receives $45,000...
asked 14 minutes ago -
Each row of the table below describes an aqueous solution at
25°C
.
The second column...
asked 19 minutes ago -
A horizontal wire is at y = 0. Current travels in the +x
direction. The magnetic...
asked 19 minutes ago -
Let X be a continuous random variable whose PDF is Let X be a
continuous random...
asked 40 minutes ago -
Martinez Company’s relevant range of production is 7,500 units
to 12,500 units. When it produces and...
asked 38 minutes ago -
A football with a mass of 1.2 kg is kicked from ground level to
a height...
asked 44 minutes ago -
Remember: Changes in supply determinants shift supply, and
changes in demand determinants shift demand. We say...
asked 43 minutes ago -
Why is the answer b), for this question? I came up with C) for
my incorrect...
asked 49 minutes ago -
Suppose that you know that in the population of full-time
employees in the United States, the...
asked 1 hour ago