(25pts) 1. Draw and analyze a four resister BJT (CE) bias circuit with the following values:...

Question

Question

(25pts) 1. Draw and analyze a four resister BJT (CE) bias circuit with the following values: Ri=70k12, R2=100 k 2, Rc=5 k1, R

engineering Electrical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

solution :-) Nec= 16v Ice RC= NB Vere IR P-250 an RE 3y ay wal tage disision sule VB = 16x100 Van Ng = 9.412 volt, Ruth RIR -

Add a comment

Answer 2

Similar Homework Help Questions

(25pts) 1. Draw and analyze a four resister BJT (CE) bias circuit with the following values:...

(25pts) 1. Draw and analyze a four resister BJT (CE) bias circuit with the following values: Ri=70 k 2, Rz=100 k., Rc=5k92, Re=3 k2 and Voc=16 V. Find the operating points Ico and VCEQ Assume a BJT transistor (npn) with B=250 and VBe=0.7V
(25pts) 2. Design a four resister BJT (CE) bias circuit (using method 1 or 2) for...

(25pts) 2. Design a four resister BJT (CE) bias circuit (using method 1 or 2) for the following specifications: loq=1.5 mA, VCEQ=5 V, Vcc=14 V. Find all resistor values. Assume a BJT transistor (npn) with B=180 and V Be=0.7V Draw the designed circuit with all values.
I keep getting the wrong answer from everyone else pls help me get the right answer For the BJT bias circuit shown, what value of Rc in kilohms is needed to allow the maximum possible peak-to-peak si...

I keep getting the wrong answer from everyone else pls help me get the right answer For the BJT bias circuit shown, what value of Rc in kilohms is needed to allow the maximum possible peak-to-peak signal swing on the collector without clipping? Use Vcc-9V, Vee--7V, Vb-1.2V, and Re -9.9k2. Assume that to keep the transistor in the forward-active region, the base-collector junction cannot be forward biased. Use B 20 and Vbe(on) 0.7V. Neglect the effects of base-width modulation. Vcc...

[1] The circuit diagram on the left below is a common emitter amplifier. It is the...

[1] The circuit diagram on the left below is a common emitter amplifier. It is the full complement of components for this type of amplifier ready for AC analysis. This amplifier will be discussed in lecture prior to the lab exercises. However, with the circuit including only Rc. RE, Ri, and R2 as shown in the figure on the right, proceed with the design for a DC operating point of the common emitter amplifier. The following parameters are given: Vcc...
6.5 BI C2 Cl sig in 0 Design the bias circuit of the CE amplifier shown...

6.5 BI C2 Cl sig in 0 Design the bias circuit of the CE amplifier shown to obtain IE= 0.5 mA and Vc= +6 V. Design for a dc voltage at the base of 5 V and a current through RB2 of 50 μΑ. Let Vcc-+15 V, β-100, and VBE 0.7 V. a) Specify the values of RBi, RB2, RE, and Rc b) Also give the values of the BJT small-signal parameters gm, rr , and ro at the bias...
draw a base biased circuit and refered to question 5 and complete table. please draw the fixed bias diagram circuit and follow throught step on the next question. Figure 1. Bipolar junction tran...

draw a base biased circuit and refered to question 5 and complete table. please draw the fixed bias diagram circuit and follow throught step on the next question. Figure 1. Bipolar junction transistor under base bias/fixed bias 5. In the circuit drawn in Figure 1, label the components with the following values: Base voltage, Collector voltage10V Base resistance Collector resistance Base - emitter voltage 2.7 k2 0.7 V 160 6. Connect the circuit drawn in Figure 1 on the breadboard....

Problem 1: BJT DC Circuits Analyze the four circuits below, first analytically and then verify us...

Problem 1: BJT DC Circuits Analyze the four circuits below, first analytically and then verify using simulations in PSPICE/Multisim. You have to solve each circuit that is, find the status of the BUT (active, saturation or cutoff mode) and then find all the node voltages and all the currents. Whenever you solve manually always make the following assumptions: for npn BIT VE-0.7V (if the BE junction is forward biased) for pap BIT VEB-0.7V (if the BE junction is forward biased)...
F LOpoint For the circuit shown in Figure 3 3. 1. Draw the DC equivalent circuit...

F LOpoint For the circuit shown in Figure 3 3. 1. Draw the DC equivalent circuit by opening caps and shorting inductors 2. Analyze the DC equivalent circuit as we have in previous labs (assume a region, analyze and check assumptions). Check your DC operating point using LT Spice. 3. Calculate the small signal parameters (transconductance, output resistance, input resistance) 4. Draw the AC equivalent circuit by shorting de voltage sources, opening dc current sources, shorting caps and opening inductors....
A common source amplifier circuit based on a single n-channel MOSFET is shown in Figure 4b. Assume that the transconductance gm-60 mS (equivalent to mA/ V) and drain source resistance, os,...

A common source amplifier circuit based on a single n-channel MOSFET is shown in Figure 4b. Assume that the transconductance gm-60 mS (equivalent to mA/ V) and drain source resistance, os, is so large it may be neglected. 0) Calculate the open circuit voltage gain Av Yout/ Vis. i) The amplifier has a load of 10 k2. Determine the current gain Va. = 12 V 150k 4k3 Vout Vin 200k GND = 0 V Figure 4b a) State the name...

(25pts) 1. Draw and analyze a four resister BJT (CE) bias circuit with the following values:...

Homework Answers