Given input clock frequency = 16 MHz
that means, clock period = 1/16MHz = 62.5ns
We need one-shot Tiva timer to time out in 133 ms.
So timer should be loaded with initial value = 133msec/62.5ns = 2128000 clocks
Answer: 2128000 clocks.
If we wanted a one-shot Tiva timer to time out in 133 ms, what initial value...
3. A watchdog timer that uses timer with prescaler is connected to a12 MHz oscillator timeout should occur if the function watchdog reset is not called within 5 minutes. value should be loaded into the up-counter pair when the function is called. What Time with prescaler 16-bit서overflow. Clk Prescaler 16-bit up tosystem reset or z→ 16 - counter interrupt Mode Finding resolution and then the range
Introduction In this lab, you will explore the design of counters and timers by designing a simple kitchen timer. Requirements The timer has two pushbutton inputs, reset_n, and run_stop. It has one 4-bit output, seconds that drives four LEDs and a one-bit output, alarm, that drives one LED. It also has a clock input, clk. Your timer should operate as follows: The timer can be in one of two states: run=0 and run=1. run is set to 0 when reset_n...
Clock Divider
can i get some simple explanation ( what I'm suppose to
understand from this)
my lecturer explains it but I honestly don't understand what
statements he's trying to make
my understanding :
there's a frequency input of 512 Mhz, since we know 8 bit
counter can count up to 256, it will do it once before it rolls
overload (???)
can someone please clarify and point out the important facts
that i should be undertanding
please and...
Clock Divider
can i get some simple explanation ( what I'm suppose to
understand from this)
my lecturer explains it but I honestly don't understand what
statements he's trying to make
my understanding :
there's a frequency input of 512 Mhz, since we know 8 bit
counter can count up to 256, it will do it once before it rolls
overload (???)
can someone please clarify and point out the important facts
that i should be undertanding
please and...
At a circus, a clown is being shot out of a cannon. This is a good thing because clowns are terrifying. The cannon’s barrel makes an angle of 35 degrees with the ground and the initial velocity has magnitude 10.4 m/s. The end of the barrel is 1.0 m above the ground. A 1.0 m thick mattress, with sides 2.0 m long, is placed so its closest edge is a horizontal distance of 10.0 m from the end of the...
Really need help with 1) How
fast was Stan going at the time of impact?
Stan the Man, from the local circus, was a human cannon ball. While practicing one day, he was shot out of a cannon and into a canyon and subsequently died. It is believed it was murder but suicide cannot be ruled out, yet. Here are the facts of the case One afternoon, Stan climbed into the cannon for reasons we do not know. According to...
The Flying Physics Brothers, Stu and Lou, end their act by both being shot out of cannons. They fly through the air and land at the same height they left the cannons. Assume air resistance can be neglected Stu's initial speed is 15.91 m/s and Lou's initial speed is 20.28 m/s. Stu leaves the cannon at an angle of 64.8° and Lou leaves the cannon at an angle of 35.1°. As usual, the angles are measured upwards from the positive-x...
16 What does this script print? de do lots of stuff initial value): out of for in range (1, 4): counter i counter = 10 do lots of stuft (counter) print (counter) Select one: O 13 O An error message. O 10 O 16 Previous page Type here to search *12 WERTY U L O so F G H uki
he Flying Physics Brothers, Stu and Lou, end their act by both being shot out of cannons. They fly through the air and land at the same height they left the cannons. Assume air resistance can be neglected. Stu's initial speed is 14.63 m/s and Lou's initial speed is 23.90 m/s. Stu leaves the cannon at an angle of 60.6o and Lou leaves the cannon at an angle of 28.1o. As usual, the angles are measured upwards from the positive-x...
1. What is the average Magnetic Flux through one single coil at
the initial position of the bar magnet using
initial = 2.32 x 10-3 T and
= 2.292 x 10-4 m2.
2. What is the total average Magnetic Flux through all 1600
turns in the coil at the initial position of the bar magnet? This
is the value for
initial.
3a. What is the average Magnetic Flux through one single
coil?
b. What is the total average Magnetic Flux...