Question

Use the diagram and questions on the reverse side to solve the problem below. If necessary, attach extra paper A load must be suspended 6 m below a high ceiling using cables attached to two supports that are 2 m apart. How far below the ceiling (x in the figure) should the cables be joined to minimize the total length of cable used? What is the minimum length of cable required?
media%2F291%2F291996a4-4440-4ffa-9c8c-33
0 0
Add a comment Improve this question Transcribed image text
Answer #1

et beano Meter the eatenう @pF. Bd. 一か2 G m CIten)cable belaidd to nnin.ibed tto (le The Minimum louhe,臥 Cable nog uived

Add a comment
Know the answer?
Add Answer to:
Use the diagram and questions on the reverse side to solve the problem below. If necessary,...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • You might get partial grades from this question. Solve this problem on paper, then, in 5...

    You might get partial grades from this question. Solve this problem on paper, then, in 5 minutes after you finish your exam, take its photo with your ID on it and e-mail to the instructor motor flexible cables elevator Vo=1 m/s E The elevator in the figure is suspended by four flexible steel cables of diameter d=13 mm and modulus of elasticity E = 200 GPa. While it is going down with a speed of Vo = co = 1...

  • Please help! I need help finding and solving equations of equilibrium to find the max tension in ...

    please help! I need help finding and solving equations of equilibrium to find the max tension in the cables and the angle that results in the maximum tension, I also have pictures below of the work I have so far all I really need is equations for the 4 cable part and that's it but I put the whole assignment so you could see thanks! Tower Support System Challenge Challenge Scenario: Due to weather conditions, a major communication tower n...

  • I Solve any five of following questions (show all the necessary steps) and submit until August-01-2020...

    I Solve any five of following questions (show all the necessary steps) and submit until August-01-2020 in PDF file format 1. Draw the shear and bending-moment diagrams for the beam and loading shown below and A B 400 mm 400 mm 250 mm 12 kN 8 KN If the shaft has a diameter of 6cm, Determine the A. Shear forces B. Moment of arms C. The absolute maximum Bending stress in the shaft. 2. Two solid cylindrical rods AB and...

  • pleas help me in this do any question you know using National Electrical Code 2011 Applied Electricity NEC...

    pleas help me in this do any question you know using National Electrical Code 2011 Applied Electricity NEC worksheet t hree Copper conductors with THHN insulation run in Electrical A branch-circuit Consther conductors. The conductor terminations are rated for a maximum ure in the area of this installation is not expected to exceed 30C size 8 AWG, the maximum ampacity of the conductors If the conductors for this circuit are permitted A 40 amperes. B. 50 amperes. to be used...

  • Fatty Acid Metabolism. The reactions of the fatty acid spiral are shown below. Use the description...

    Fatty Acid Metabolism. The reactions of the fatty acid spiral are shown below. Use the description on the left side of the page to classify the reactions and fill in the boxes on the right side of the page Activation Step. The activation of the fatty acid begins by the addition of CoA which will carry the fatty acid from the cytosol into the mitochondria. The product, which is a fatty acid with a CoA attached, is known as a...

  • summatize the following info and break them into differeng key points. write them in yojr own...

    summatize the following info and break them into differeng key points. write them in yojr own words   apartus 6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...

  • summarizr the followung info and write them in your own words and break them into different...

    summarizr the followung info and write them in your own words and break them into different key points.   6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...

  • Consider a cylindrical capacitor like that shown in Fig. 24.6. Let d = rb − ra...

    Consider a cylindrical capacitor like that shown in Fig. 24.6. Let d = rb − ra be the spacing between the inner and outer conductors. (a) Let the radii of the two conductors be only slightly different, so that d << ra. Show that the result derived in Example 24.4 (Section 24.1) for the capacitance of a cylindrical capacitor then reduces to Eq. (24.2), the equation for the capacitance of a parallel-plate capacitor, with A being the surface area of...

  • please help and thank you Materials Needed per class: 1 box of 24 microscope slides of...

    please help and thank you Materials Needed per class: 1 box of 24 microscope slides of meiosis 1 1 box of 24 microscope slides of meiosis 2 red and yellow popbead chromosome kits Objectives To become familiar with the process of meiosis and to be able to identify the principal phases of meiosis To understand how the process of meiosis is similar to mitosis and how it differs from mitosis Introduction The genetic information of a cell is encoded in...

  • 10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated...

    10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT