pure radial flow blade design that operates at 1200 rpm, delivering 18 m^3/h of water at...
pure radial flow blade design that operates at 1200 rpm, delivering 18 m^3/h of water at 10 bars. The slip factor is 0.9. Flow enters the "impeller eye" along the pure axial direction.
a. Determine the impeller radius
b. The impeller height at the outlet is 5 cm. find velocity along both radial and tangential directions at the impeller outlet.
Homework Answers
Add Answer to:
pure radial flow blade design that operates at 1200 rpm,
delivering 18 m^3/h of water at...
QUESTION 2 A 30 Watt brake horsepower centrifugal blower rotates at 1200 rpm and delivers air...
QUESTION 2 A 30 Watt brake horsepower centrifugal blower rotates at 1200 rpm and delivers air at 0.4 m3/s. The air enters the impeller radially and exits at an angle ?2-34° from radial. The impeller inlet radius is 40 mm and the outlet radius is 100 mm. Assuming 100% efficiency, determine the net head produced by this blower, the tangential velocity component at the outlet (Ved, the outlet blade width and the exit blade angle (Pa). [Use for air: Pai...
The rotor shown below rotates with an angular velocity of 2000 rpm. Assume that the fluid...
The rotor shown below rotates with an angular velocity of 2000 rpm. Assume that the fluid enters in the radial direction and the relative velocity is tangent to the blades across the entire rotor. Find the exit normal velocity (ft/s) and exit velocity of the blade in terms of inlet. Draw the inlet and outlet velocity triangles. Is the device a pump or a turbine? Explain. Hint: create a velocity triangle at (1) and (2) and compare them. Does the...
A centrifugal pump operating at 1200 rpm is delivering 10 m^3/h of water at 10 bars...
A centrifugal pump operating at 1200 rpm is delivering 10 m^3/h
of water at 10 bars and requires 6 kW of shaft power at the best
efficiency point.
a. Determine the effiecincy of the pump
b. Deterine the flow rate, discharge pressire, and required
shaft power at the corresponding point of 1800 rpm.
4. A centrifugal pump operating at 1200 rpm is delivering 18 m2/h of water at 10 bars and requires 6 kW of shaft power at the best...
(b) A centrifugal pump rotates at 750 rpm. Water enters the impeller normal to the blades...
(b) A centrifugal pump rotates at 750 rpm. Water enters the impeller normal to the blades (GJ 0°) and exits at an angle of 35° from radial (α,- 35°). The inlet radius is r12.0 cm, at which the blade width bi 18.0 cm. The outlet radius is r2 24.0 cm, at which the blade width b 16.2 cm. The volume flow rate is 0.573 m/s. Assuming 100 percent efficiency. Given density of water to be 998 kg/m3 i Calculate the...
The centrifugal pump as described in Q5.8 is operating with a pre-whirl of 10° (i.e. Ui is inclin...
The centrifugal pump as described in Q5.8 is operating with a pre-whirl of 10° (i.e. Ui is inclined by 10° from the radial axis in the rotational direction). The centrifugal pump delivers 0.45 m3/s ofwater when it is running at the angular velocity of ω-1200 rpm Sketch the velocity triangles at inlet and exit of the impeller and hence determine the following items by assuming (a) negligible losses; and (b) Vi enters the impeller with θ| and V2 leaves with...
C) Axial-flow compressor Answer 3) Specifie speed (0.) for the compressor compressor should selected? application is 0.9. Which of the following type of 52 th Reciprocating compressor B) none of t...
C) Axial-flow compressor Answer 3) Specifie speed (0.) for the compressor compressor should selected? application is 0.9. Which of the following type of 52 th Reciprocating compressor B) none of these A) Centrifug al compressor 1,) compressor D) Centrifugal fan 6) &7) The compressor is tested at sea level on a stationary atmospheric temperature and pressure is design operating point, the mass flow rate through the compr rotational speed is 7000 rpm. Determine the flow compressor is operating at the...
QUESTION 2 A 30 Watt brake horsepower centrifugal blower rotates at 1200 rpm and delivers air at 0.4 m3/s. The air enters the impeller radially and exits at an angle ?2-34° from radial. The impeller inlet radius is 40 mm and the outlet radius is 100 mm. Assuming 100% efficiency, determine the net head produced by this blower, the tangential velocity component at the outlet (Ved, the outlet blade width and the exit blade angle (Pa). [Use for air: Pai...
The rotor shown below rotates with an angular velocity of 2000 rpm. Assume that the fluid enters in the radial direction and the relative velocity is tangent to the blades across the entire rotor. Find the exit normal velocity (ft/s) and exit velocity of the blade in terms of inlet. Draw the inlet and outlet velocity triangles. Is the device a pump or a turbine? Explain. Hint: create a velocity triangle at (1) and (2) and compare them. Does the...
A centrifugal pump operating at 1200 rpm is delivering 10 m^3/h
of water at 10 bars and requires 6 kW of shaft power at the best
efficiency point.
a. Determine the effiecincy of the pump
b. Deterine the flow rate, discharge pressire, and required
shaft power at the corresponding point of 1800 rpm.
4. A centrifugal pump operating at 1200 rpm is delivering 18 m2/h of water at 10 bars and requires 6 kW of shaft power at the best...
(b) A centrifugal pump rotates at 750 rpm. Water enters the impeller normal to the blades (GJ 0°) and exits at an angle of 35° from radial (α,- 35°). The inlet radius is r12.0 cm, at which the blade width bi 18.0 cm. The outlet radius is r2 24.0 cm, at which the blade width b 16.2 cm. The volume flow rate is 0.573 m/s. Assuming 100 percent efficiency. Given density of water to be 998 kg/m3 i Calculate the...
The centrifugal pump as described in Q5.8 is operating with a pre-whirl of 10° (i.e. Ui is inclined by 10° from the radial axis in the rotational direction). The centrifugal pump delivers 0.45 m3/s ofwater when it is running at the angular velocity of ω-1200 rpm Sketch the velocity triangles at inlet and exit of the impeller and hence determine the following items by assuming (a) negligible losses; and (b) Vi enters the impeller with θ| and V2 leaves with...
C) Axial-flow compressor Answer 3) Specifie speed (0.) for the compressor compressor should selected? application is 0.9. Which of the following type of 52 th Reciprocating compressor B) none of these A) Centrifug al compressor 1,) compressor D) Centrifugal fan 6) &7) The compressor is tested at sea level on a stationary atmospheric temperature and pressure is design operating point, the mass flow rate through the compr rotational speed is 7000 rpm. Determine the flow compressor is operating at the...
Most questions answered within 3 hours.
-
There are two flasks on the bench top, one flask contains a 0.50
M NaCl solution...
asked 1 minute from now -
Which of the following aqueous solutions are good buffer
systems?
.
0.10 M hydrofluoric acid +...
asked 9 seconds ago -
2. An S election is terminated if the S corporation has passive
investment income in excess...
asked 2 minutes ago -
Part of an ANOVA table is shown below.
Source of
Variation
Sum of
Squares
Degrees of...
asked 18 minutes ago -
Business process improvement initiatives often include
introducing new technology to support the new or changed ways...
asked 25 minutes ago -
Review your choice of either Agile or the Waterfall models and
for each of the 22...
asked 26 minutes ago -
Suppose an x distribution has mean μ = 4.
Consider two corresponding
x
distributions, the first...
asked 28 minutes ago -
A study of the effects of exercise used rats bred to have high
or low capacity...
asked 54 minutes ago -
Using your data from the experiment, calculate the initial moles
of HCl that you started with....
asked 55 minutes ago -
Suppose you want to make 500 mL of a 0.20 M Tris buffer at pH
8.0....
asked 56 minutes ago -
The titanic hit an iceberg estimated to be half of her mass.
Before hitting the iceberg,...
asked 1 hour ago -
3. The top four firms in Industry A have market shares of 30,
25, 10, and...
asked 1 hour ago