You need to design a circuit that implements the functions in the following table:
S0 and S1 are 1-bit control inputs to select the function of the
circuit. Inputs A and B are 4-bit numbers in 2s complement form.
The output is also a 4-bit number in 2s complement form. You are
allowed to use only one TTL 7483 4-bit adder to implement all the
functions. But any number of other components (except the adder)
can be used.
HINT: Design a combinational logic circuit to modify the input B
and the “carry input” of the adder depending on the control inputs
S0 and S1.
Side Note:
I found the following solutions online, however, I unable to understand how they were able to reach these solutions because there were no real explanations. I would really appreciate a detailed solution as to how they reached these conclusions, thank you!
You need to design a circuit that implements the functions in the following table: S0 and...
Please solve the problems from 2_5 Digital system Problem 2 Design a combinational circuit with inputs a, b, c, d and outputs w, x, y, z. Assume that the inputs a, b, c d represent a 4-bit signed number (2s complement). The output is also a signed number in 2s complement which is 5 greater than the input if the input is less than 2, and is 2 less than the input if the input is greater than or equal...
This section gives you freedom to come up with your own solutions. An Arithmetic and Logic Unit (ALU) is a combinational circuit that performs logic and arithmetic micro-operations on a pair of 4-bit operands. The operations performed by an ALU are controlled by a set of function-select inputs. In this lab you will design a 4-bit ALU with 3 function-select inputs: Mode M, Select S1 and S0 inputs. The mode input M selects between a Logic (M=0) and Arithmetic (M=1)...
EE252 100 Points Digital Design I Two's Complement Subtraction and Add / Subtract Circuits Homework 3. (25 Pts) The following circuit uses two 7483 (4-bit adder) ICs, labeled 7483-1 and 7483-2, respectively. Answer the questions for EACH of the following THREE CASES: Case 1: D=0010, and E = 0110 Case 2: D = 1000, and E = 0101 Case 3: D = 1000, and E = 1001 a. (6 Pts - 2 Pts per Case) What are the binary inputs...
1- Please answer all the question 2- with clear handwriting Thank you, 3. Design a combinational circuit with inputs a, b, c, d and outputs w, z, y, z, where the input and output both represent a signed numbers (2s complement). The output is 7 less than the input, if the input is positive, or zero. If the input is negative, the output is 3 greater than the input. 7. Use the Boolean functions developed in problem #3 to create...
Verify that your design can be represented by the circuit below. 120 Full-Adder circuit Many of the logic gates you require may not exist in standard TTL/CMOS 74 series family of logic. For example in future designs you may require a 50 input OR gate. The 74 series does not have a 50 input OR gate. For your 1 bit adder you will have the following devices: 1 quad 2 IP NAND, 1 TRIPLE 3 IP NAND, 7400 7410 7404...
Design a four-bit combinational circuit 2’s complementer. (The output generates the 2’s complement of the input binary number.) Show that the circuit can be constructed with exclusive-OR gates. Can you predict what the output functions are for a five-bit 2’s complementer? 1. Truth table 2. Logic circuit with exclusive-OR gates 3.The output functions for a five-bit 2’s complementer
5) Decoders: Given the following circuit, S0 and S1 are computed using a 4-2 priority encoder with the priorities indicated on the figure. (hint: IDLE signal is always 0, if any of the inputs 10,11,12, or 13 is 1) 6 points) 4-to-2 Priority Encoder 10 YO YI 13 IDLE 13> 11 > 12>10 12 Full c Adder So Fill the following table showing the output signals S0 and SI given the input signals w, x, y, a) and z. Prof...
Problem 1(8 points): Design a 3-bit register which has the following function table. Neatly design and show the complete circuit diagram of this 3-bit register Mode Control Register S1 SO Operation No Change Parallel Load Shift Up Complement Problem 1(8 points): Design a 3-bit register which has the following function table. Neatly design and show the complete circuit diagram of this 3-bit register Mode Control Register S1 SO Operation No Change Parallel Load Shift Up Complement
For this problem, you are to design a simple combinational logic circuit The circuit is a 2- bit priority encoder with inputs I2 and I1 and outputs Z1 and Z0. The circuit behaves as follows: • If I2I1 = 00, then Z1Z0 = 00 (no active input) • If I2I1 = 01, then Z1Z0 = 01 (low-priority input, X1, is active) • If I2I1 = 1-, then Z1Z0 = 10 (high-priority input, X2, is active) Note that...
Please solve the problems from 1_5 Digital system Complete the following homework problems. Show all work (making sure it is legible) and circle all answers for clarity Problem 1 w3 w4 B w1 a) Determine Boolean functions for intermediate outputs w,w2,w3, and w4 as well as the output signals X and Y. b) Construct a truth table showing the intermediate outputs wl,w2,w3, and w4 as well as the output signals X and Y c) Use K-maps to find simplified expressions...