Representation of states s0,s1,s2,s3 .
X,Y are inputs have 4 States
3. (20 points) For the circuit given below, draw the state machine diagram. CLK A' CLK...
resetn clk- PROBLEM 3 (20 PTS) . Given the following State Machine Diagram. (10 pts). ✓ Provide the State Diagram (any representation) and the Excitation Table, ✓ Provide the Excitation equations and the Boolean equation for z. w: input, z: output, lilo: state.
1. Given the state diagram shown below for a state machine with one-bit input W and two-bit output Z: a. (20 points) Using the state assignments below, make the state-assigned table. Let S0 = 001, S1 = 010, and S2 = 100. b. (20 points) Let the state variables be Y2, Y1, and Y0. Derive an expression for each of the next state variables. c. (10 points) Derive expressions for the output of this state diagram. d. (20 points) Draw...
Finish C and D 3) The circuit pictured below is a clocked synchronous state machine with state variables 02, 01,and Q0.(20 points) 02 01 CLK a) Determine the state equations for 02*, 01*,00* (6 points) Form A
4. (20 points) Draw a state diagram for Mealy Machine that your state diagram minimum? Prove it. accepts every occurrence of the staring 10101. I 4. (20 points) Draw a state diagram for Mealy Machine that your state diagram minimum? Prove it. accepts every occurrence of the staring 10101. I
SEQUENCE is 101 In Lab Procedure 1. Draw the state diagram of the state machine below and show it to the lab instructor. 2. Fill the state table. 3. Assign State numbers 4. Find simplified Expressions (State Equations) for the flip-flops 5. Draw the circuit diagram using NAND GATES ONLY for the state machine STATE DIAGRAM:: STATE TABLE:: State Table Next State Qc Y DA DB Dc Present State QA Qв 0 0 0 0 0 0 0 0 0...
Suppose a sequential logic circuit has an input X and a clock input CLK. The outputs are Qi,Qo, and Y, and the next state table is as shown below Q00 X-0 X=1 01 10 01 10 0 0 0 a) Is this a Moore circuit or Mealy circuit? b) What does this cireuit do when the input X - c) What does this circuit do when the input X 1? d) Suppose the initial values of the state are QiQ...
Study the following circuit and corresponding waveforms: a) D Q Clock CLK Q Undefined 01 02 Undefined Q Undefined Undefined Undefined Identify the waveforms that correspond to Qa, Qb and Qc. Provide the name of the components that produce Qa, Qb and Qc. (Note: one answer is none of the above.) (6 marks) b) Study the following circuit: D D D CLK CLK CLK CLK Explain why this will not implement a shift register. Your answer should include a waveform...
b) For the circuit below, draw the timing diagram for outputs X and Y for the CLK signal shown below. Note that the flip-flops are negative-edge-triggered. Ignore the propagation delays. Assume X=Y=0 at the start. (6 Points) LO 7x CLK CLK d oo Loy CLK
3. (16 pts.) A sequential circuit design is shown in the following diagram CLK CLK Frt Trl Frl FF1 D-FF clk-to-q propagation delay tpcq 15 ps D-FF clk-to-q contamination delay tccq-10 ps D-FF data setup time ts-15 ps D-FF data hold time th = 10 ps Gate 2-input NAND 2-input NOR 2-input XOIR NOT Tpd(ps) Tea(ps) 15 25 35 10 10 15 25 (8 pts.) Calculate the maximum clock frequency for reliable operation assuming there is no clock skew (8...
1. a) Complete the waveform templates for the Master –Slave D-flip-flop below with given D, CLK, CLEAR, and PRESET signals. Neglect the propagation delays. b) Does it have positive or negative edge triggering with respect to CLK? c) Are the asynchronous PRESET and CLEAR active-high or active-low? 2. Enabling of data load in the D-flip-flop was implemented with a 2-to-1 multiplexer as show below. The D-flip-flop has the positive edge triggering and the active-low asynchronous clear. a) Is the Enable...