Based on the VGS measurement, determine the drain current for the circuit. -8V San 2 V...

Question

Question

Answer 1

Answer #1

sol +8t LET 4.7k2 Led Here Given VGs=2 since Vs=ov VG = VG- Vo = VG-o = VG VG = VGS = 2 V Here a lo Megg ohm resistor is con

Answer 2

Similar Homework Help Questions

nMOS transistor is biased width Vds = 2 V and Vgs = 1.1 V. Assume k...

nMOS transistor is biased width Vds = 2 V and Vgs = 1.1 V. Assume k = 2 mA and VT = 0.5 V. Calculate the drain current in mA.
Determine gm in the circuit if IDSS=10mA and VGS(off)= -8V . 1.41mS 2.5mS undefined 1.875mS + 20...

Determine gm in the circuit if IDSS=10mA and VGS(off)= -8V . 1.41mS 2.5mS undefined 1.875mS + 20 ha 301 A 076
Given: IDSS 15mA; VGS(off)-8v, determine the a. ID b. VGS c. VDS d. Av (voltage gain) +5 V 1.2kn ...

Given: IDSS 15mA; VGS(off)-8v, determine the a. ID b. VGS c. VDS d. Av (voltage gain) +5 V 1.2kn 2.2 kn 0.1 μF -3.8 mS 22 kΩ 0.1 μF 0.1 μF 4.7 MII o kn 10 MI 560 Ω 0.1 μF Given: IDSS 15mA; VGS(off)-8v, determine the a. ID b. VGS c. VDS d. Av (voltage gain) +5 V 1.2kn 2.2 kn 0.1 μF -3.8 mS 22 kΩ 0.1 μF 0.1 μF 4.7 MII o kn 10 MI 560 Ω...

3. In the circuit in Figure 3, V. = 8V. Determine the value of Is. (Ans:...

3. In the circuit in Figure 3, V. = 8V. Determine the value of Is. (Ans: 12.56mA) 9 kΩ Ι 2 ΚΩ νοξ6 kΩ Is O 3 κρξ ξ5 ΚΩ Figure 3
1. Consider NMOS transistor in the circuit that has u.Cox = 0.4 mA/V?, W/L = 25,...

1. Consider NMOS transistor in the circuit that has u.Cox = 0.4 mA/V?, W/L = 25, and V.=0.4V. (20 pts) (a) Find the value of Vas that results in saturation mode operation with a lp current of 0.1 mA. Neglect the Early effect. (2.5 pts) +1.5 V in BRD (b) Find the value of Rp that results in a de drain voltage of 0.5V. (2.5 pts) = = = (e) Find gw and r, at the de operating point specified...
2. Consider the JFET self-bias network shown. VDD 10V 500Ω Vos loss = 20 mA + VGs Rs 2502 0.75 M2...

2. Consider the JFET self-bias network shown. VDD 10V 500Ω Vos loss = 20 mA + VGs Rs 2502 0.75 M2 a) Using a graphical approach, determine Vos and I b) Repeat, assuming that Rs has been doubled to 500 S2 but all other aspects of the circuit remain unchanged. Does doubling Rs cause the drain current to decrease to one half of the original value? Why or why not? 2. Consider the JFET self-bias network shown. VDD 10V 500Ω...

Voltage amplifiers are available with Avoc= 8V/V, Rin = 1.8kOhms, Ro=850 Ohms. With a 12 V...

Voltage amplifiers are available with Avoc= 8V/V, Rin = 1.8kOhms, Ro=850 Ohms. With a 12 V DC power source, each amplifier consumes 1.5 mA average current. a. How many amplifiers do you need to cascade to get at least a 1000 voltage gain with a load resistance of 1.0 kΩ? b. What is the voltage gain Av obtained? (Respond with a rounded whole number) c.For the cascade connection, find the open circuit voltage gain. d. If you have a 1.5...
Question 26 Ip) of all transistors in the circuit. You may ignore the influence of channel-length modulation and...

Question 26 Ip) of all transistors in the circuit. You may ignore the influence of channel-length modulation and body effect in your bias calculations Consider the circuit shown in Figure 7. Determine the bias point (VGs, Vps, VDD R R IREF VOUT VCM-n 2 VCM 2 Q3 VDD 5 V VCM 2 V Vt 0.5 V kn1 8 mA/V2 kn2 16 mAV2 kn3 kn4 = 8 mA/V2 1 R 3 kn IREF = 1 mA Fig. 7 Select the correct...
An NMOS transistor with parameters VTh=1 V, k’=100 uA/V2 , W = 10 um, and L=1...

An NMOS transistor with parameters VTh=1 V, k’=100 uA/V2 , W = 10 um, and L=1 um has a VGS=2 V. Find the drain current when: a. VDS=0.5 V b. VDS=2 V c. VDS=3 V Answers: a) 374 uA b) 0.5 mA c) 0.5 mA please show your work :)

1.) 120 pointsl The parameters of n-channel enhancement MOSFET in the amplifier circuit below are...

1.) 120 pointsl The parameters of n-channel enhancement MOSFET in the amplifier circuit below are: 2.042 mA/V2, 1 Val ½ 2.4 V, Kn 150 V a.) Find quiescent values: drain current i, gate-to-source voltage vGs, and drain-to-source voltage vDs b.) Determine AC model parameters: gm and ro c.) Determine amplifier model parameters: Ri, Ro and Avo d) Determine the output voltage Vl across the load RL ǐfv, 1 mYn +VDD GI〈 R ls R Mi RL 1.) 120 pointsl The...