sex
For the following circuit + Vc - 560 03 ? 47003 Vout 5v++ Complete the table...
680 22 W + Vin 1. Ø 470 8} Vo - Lid Vout 0.5 V Complete the table below. Show all work. (20 points) Diode status (on or off) Vout just turning on 4 V Plot Vout as a function of Vin for –5 V < Vin < 5 V. (4 points)
Problem #5 [10 points]: Design a circuit with the following criteria. Assume existence of +5V power supply. Draw your circuit and show your work. i. Input signal that operates between Vin -5V- +5V, and capable of sourcing or sinking 500 x 10^-6 A. ii. Output signal nominally outputs between Vout 0V 5V, and capable of sinking 1 mA from an external device with an output no more than 0.1 V Problem #5 [10 points]: Design a circuit with the following...
4. (25 points) (Show all work) Design an inverter circuit using a NMOS transistor and a resistor with Vout-5.0 when Vin-OV and Vout-0.3 V when Vin-SV with Kn-300uA/V" and a VrN = 1 V. Use ID-Kn(VGS-VTNJVDs. You have a 5V supply available to power the circuit.
Given the biased diode circuit below answer the following questions. Assume, lD = Is e vd/nUT, n =1, Cb is infinite, and vd = 600mV at 800uA, 50 points 2. VDD 200uA The current through each diode at VaV The small signal ac circuit, The transfer function. a. and voltage Cb Cb and Vc vin vout b. c. Va AC Vc 100uA
Draw a circuit to output the following wave as 1V pk-pk sine wave centered at 0V and output to be out of phase 180degrees with respect to input. Problem #5 [10 points]: Design a circuit with the following criteria. Assume existence of +5V power supply. Draw your circuit and show your work. i. Input signal that operates between Vin -5V- +5V, and capable of sourcing or sinking 500 x 10^-6 A. ii. Output signal nominally outputs between Vout 0V 5V,...
Build an Op-Amp Circuit Network. Note you only have a power source of 5V available. You have a voltage signal that latches at a constant 1.5V. Create a difference circuit to produce an output voltage of 2V. Put P/Ns and element values in your design. Show your work. From part a)’s output voltage, assign that now as a reference voltage (Vref) to compare to an analog sensor signal (Vin) that can range between 0V – 5V. Make sure your circuit...
Prob. 2. For the following circuit, i. Draw the transfer characteristic of the circuit (Sketch Vo(t) vs Vin(t)). ii. Sketch the output waveform, v.(t) for the input Vin(t) = 10 Sin(wt) V. Clearly indicate the status of each diode. Assume that both D, and D, are ideal diodes. Table: Possible Diode States # D1 D2 Result 1 Off Off 2 Off On 3 On Off | 4 On On + TOKS VD . >19
Problem 5: (20 points) Given the following circuit VIN L Vout R a) Write the loop equation for the circuit, and then find the transfer function Vout(s) H(S) = Express H(s) so that the coefficient of the s in the denominator is 1. Vin(s) b) If Vin(t) is 20u(t), find out(t). c) If Vin(t) is 20u(t) find the final value using the final value theorem (show your work), d) Assume (R/L) = 10, if the input is Vin(t) = 100...
5. (8 points) Assume Vin = 5 sinut (for 0 <<<), ideal diode model and zero initial condition across G. Now, plot the input and output as a function of time on the same plot for each circuit shown below (show every feature and value clearly) Vino th o Vout b) Vin Vout TU c) Vin Ae U i F d) o Var Vina K D BIP are
please answer all questions neatly and use Matlab for part C Vout - - Current Source Current-to-Voltage Converter SkW variable voltage 0-5V Figure 4. Current- to- voltage converter 3.- Current-to-Voltage Converter An op amp can be used to produce a voltage proportional to a given current as shown in fig. 4 a) (5 points) Derive the formula for the output voltage Vout. For full credit show all the steps of the formula derivation in a clear way, and indicate which...