Problem #5 [10 points]: Design a circuit with the following criteria. Assume existence of +5V pow...
Draw a circuit to output the following wave as 1V pk-pk sine wave centered at 0V and output to be out of phase 180degrees with respect to input. Problem #5 [10 points]: Design a circuit with the following criteria. Assume existence of +5V power supply. Draw your circuit and show your work. i. Input signal that operates between Vin -5V- +5V, and capable of sourcing or sinking 500 x 10^-6 A. ii. Output signal nominally outputs between Vout 0V 5V,...
Build an Op-Amp Circuit Network. Note you only have a power source of 5V available. You have a voltage signal that latches at a constant 1.5V. Create a difference circuit to produce an output voltage of 2V. Put P/Ns and element values in your design. Show your work. From part a)’s output voltage, assign that now as a reference voltage (Vref) to compare to an analog sensor signal (Vin) that can range between 0V – 5V. Make sure your circuit...
Q. 5(20 points) Design a transistor amplifier to supply a LED. The LED is required to turn "on" and "off " following the on/off signal from a digital output port of a microcomputer. VoFF = 0 V, Îmicroprocessor 5 mA,Vcc-5V, Vy (for the transistor) = 0.7 V, ? = 95, VCE at- Assume that the current needed to derive the LED is LED-10 mA. RB = 1 K ?, VON=5V: 0.2 VyLED (for the LED)-1.4 V, , Pmax-200 mW. Provide...
QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates from the mains and provides an output of Voc-20 V with 20% ripple, when the load current is 2 A Calculate the maximum and minimum values of the output waveform of this power supply. b. Now you will design a series voltage regulator between the power supply described in part (a) and an electronic device operating at 12 VDC...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
Problem 5: (20 points) Given the following circuit VIN L Vout R a) Write the loop equation for the circuit, and then find the transfer function Vout(s) H(S) = Express H(s) so that the coefficient of the s in the denominator is 1. Vin(s) b) If Vin(t) is 20u(t), find out(t). c) If Vin(t) is 20u(t) find the final value using the final value theorem (show your work), d) Assume (R/L) = 10, if the input is Vin(t) = 100...
You are required to design a 2-stage voltage amplifier (find values for RE, RC1, RC2) to meet the following criteria: an input resistance of 400 kΩ and an overall voltage gain equal to or greater than 250, with a resistor output load, RL. Use a common-emitter with emitter degradation (RE) stage for the input, followed by a commonemitter amplifier with bias current equal to 0.5 mA. (VCC = 20 V, βo = 200 and the DC levels of the first...
please solve the following problem 10.7 10.8 Homework Problems 227 10.7 Design a circuit that uses a 5 V power supply to illuminate an LED that has a forward voltage drop of = 2.2 V. Use only standard 5% resistors in your design, and insure that the current flowing through the LED is between 17 and 20 mA 10.8 If Q in Figure 10 23
(a) Design an inverting amplifier by choosing suitable resistor values for R1 and R2 to produce a gain of 5 when both switches Sw1 and Sw2 are open. (b) Design the bias input circuit by choosing suitable resistors R3 and R4 such that the voltage vb will be 0.5V if the positive power supply of the op-amp is connected to a 5V battery. Again both switches are open. (c) Given Sw1 is open, the amplifier is turned on for enough...
A common source amplifier circuit based on a single n-channel MOSFET is shown in Figure 4b. Assume that the transconductance gm-60 mS (equivalent to mA/ V) and drain source resistance, os, is so large it may be neglected. 0) Calculate the open circuit voltage gain Av Yout/ Vis. i) The amplifier has a load of 10 k2. Determine the current gain Va. = 12 V 150k 4k3 Vout Vin 200k GND = 0 V Figure 4b a) State the name...