Q7- Show the states of the 5-bit shift register for the specified data input and clock...
Assume that the 4-bit bidirectional shift register initially contains 0011, and the input data is High,. If the control pin for right/left is High for 2 clock pulses and Low for three more clock pulses , what are the contents after the fifth click pulse? (show detail answer)
Question #5 (3 marks): The content of a 4-bit register is initially 1001. The register is shifted six times to the right, with the serial input (SI) being 010010. What is the content of the register after each shift? --------- --------- Serial in (SI) Serial in (SI) NO D1Q1 - D 2 Q2 Io D3 03 _ Dr D3 Q3 DO QO Serial out (SO) CE CE HCE LACE 1 Shift Clock - Q3 Q2 Q1 QO 1 0 0...
show truth table for 3 bit register flip flop with 3 data input, clock input, one enable input that connnects to each FF and 3 output for each FF.
Shift Register: Design a 4-bit shift register for the following function table. Inputs are D3D2D1D0 for parallel data load, S1S0 are the mode control, and the clock. Outputs are the register bits Q3Q2Q1Q0. Show the complete logic diagram.
5) The content of a 4-bit shift register is initially 1101. The register is shifted six times to the right, with the serial input being 101101. What are the contents of the register after each shift?
Problem 7. Consider the 74x194 4-bit bidirectional universal shift register shown below Determine the operation of this circuit by filling out the table. Assume that the register is cleared initially as indicated by the first row in the table, and then connected to +5V (before time t), as shown in schematic. Also assume that t 'is that time at which a positive edge occurs in the input signal 'clock'. Si and S0 inputs (given) are used to switch between modes...
17. The 74195 in Figure 17 is a synchronous load, 4-bit parallel-access shift register. For this exercise, the input data is loaded at the first active clock edge. (12 pts) 74195 DSTM2 SH/LD QB 13 QC QD DSTMI 10t CLK ㅡㅡㅡ CLR Figure 17 Use the circuit of Figure 17 to answer the following questions: a. Is this a ring counter or a Johnson counter? (2 pts) b. How many different states are available? (2 pts) Draw the timing diagram...
17. The 74195 in Figure 17 is a synchronous load, 4-bit parallel-access shift register. For this exercise, the input data is loaded at the first active clock edge. (12 pts) 74195 DSTM2 SH/LD 2 15 QC DSTMI 10 CLK CLR Figure 17 Use the circuit of Figure 17 to answer the following questions: a. Is this a ring counter or a Johnson counter? (2 pts) b. How many different states are available? (2 pts) Draw the timing diagram (four clock...
Problem 4: Design a 2 bit register whose operation is controlled by the signals C1 and C2 as follows: (Use D- Flip Flops) Y2 Y1 C 2-Bit Register Clock SD PD1 PD2 Y1 Y2+ Operation Hold C1 C2 Y2 Y1 0 10 Shift Right Y1 SD 1 0 SD Y2 Shift Left PD2 PD1 Parallel Load 1 SD: Serial Data input PD1 PD2: Parallel Data input Problem 4: Design a 2 bit register whose operation is controlled by the signals...
b. (i) Draw the circuit diagram of a 4-bit shift register using D-flip-flop. (2 marks) (ii) Supposing the 4-bit data 1011 is to be transfer in a 4-stage shift register using D-flip- flop, right-out the corresponding output of each of the flip-flop after the 6th clock pulses. (4 marks) c. Design a synchronous counter that go through the state 3, 4, 5, 7,8, 9, 10 . (13 marks)