UUUUUUUse scriere. 10) 33 Consider figure 3.1 below and answer the questions that follow Z=2j Z=3x2,...

Question

Question

UUUUUUUse scriere. 10) 33 Consider figure 3.1 below and answer the questions that follow Z=2j Z=3x2, 20MVA 132/11kV Z =5% 2=2

engineering Electrical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

P. Oor system Given n/wo y to 90MYR be 100 MVA and 132 kV let baze MVA and Kv (RV) Base impedence MVA Zbare a too 170.242 Zme at The (Transformer) e MVAneto xf KV. 0.05 x 100 Zine 0.25 put Zopa = 28 20:25) Zope = 0.5 pu. a baseb (OOMVA and 132V at Gen

Assuming He elements Ches following typ connections to connected to powder system. give ZnZnto bault at Bun C. Le BE Ziegt 2r

012915+0.291570-5645 Pop - 2.61 poel at Bus B If = 2,61% 100 MIOS 132 2103 Pop = 1,9748A So at Bus C Il s 1,977 x 132 - 23.72

Add a comment

Answer 2

Similar Homework Help Questions

Use power base of 100MVA to change to per unit Consider the transmission system in figure...

Use power base of 100MVA to change to per unit Consider the transmission system in figure 1 below Gen 1 Тx 2 Line 1 Gen 2 Tx3 Line 4 Line 3 R F Tx 1 Gen 3 Line 2 Figure 1 Impedance and winding details are:- Generators: Gen 1 132kV, Z=0+j12.5% on 25MVA Gen 2 132kV, Z= 0+j12.5% on 25 MVA 20KV, Z 0+j10% on 25 MVA A- connected windings Gen 3 Transformers Earthed Y windings (both sides) Earthed Y...
Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which ...

Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which is 20% of the total line 2 length from Bus B Fault MVA 1524.20471 Three-phase fault level in MVA at bus A SPFL (kA) 8 MVA1 MVA2 X1 (96 X2 (96) R1 (2) R2 (Q) z' (Q) Zo (2) Rf (Q) Single phase to ground fault level (kA) at bus A Transformer 1 MVA...
QUESTION 4. A single-line diagram of a power system is shown in Figure Q3 below, where...

QUESTION 4. A single-line diagram of a power system is shown in Figure Q3 below, where negative and zero-sequence reactances are also given. The neutrals of the generator and A-Y transformers are solidly grounded. The motor neutral is grounded through a reactance X.=0.05 per unit on the motor base. Prefault voltage is VF1.05<Oº per unit whereas prefault load current is zero. Take A-Y transformer phase shifts into consideration. M Line tool X, - X2 - 200 100 MVA X =...

A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y...

A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y transformers are solidly grounded. The motor neutral is grounded through a reactance Xn 0.05 per unit on the motor base. Assume that Pre-fault voltage is takin as VF-1.0 ,0° per unit and Pre- fault load current and Δ-Y transformer phase shift are neglected In the...
Figure 1 Single line diagram b2 b3 b1 b4 grid Τι 13 A power system single line diagram is shown...

Figure 1 Single line diagram b2 b3 b1 b4 grid Τι 13 A power system single line diagram is shown in Figure 1. The single line diagram shows a synchronous generator G connected to a large 50 Hz grid via its unit transformer T and a network of three transmission lines. Relevant details of the grid, transformer, generator and overhead lines are provided in Tables I,II,II & IV respectively. A double line to ground fault occurs at bus 3 Questions....

UUUUUUUse scriere. 10) 33 Consider figure 3.1 below and answer the questions that follow Z=2j Z=3x2,...

Homework Answers

Add Answer to:
UUUUUUUse scriere. 10) 33 Consider figure 3.1 below and answer the questions that follow Z=2j Z=3x2,...

Post as a guest

Earn Coins

Use power base of 100MVA to change to per unit Consider the transmission system in figure...

Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which ...

QUESTION 4. A single-line diagram of a power system is shown in Figure Q3 below, where...

A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y...

Figure 1 Single line diagram b2 b3 b1 b4 grid Τι 13 A power system single line diagram is shown...

UUUUUUUse scriere. 10) 33 Consider figure 3.1 below and answer the questions that follow Z=2j Z=3x2,...

Homework Answers

Add Answer to: UUUUUUUse scriere. 10) 33 Consider figure 3.1 below and answer the questions that follow Z=2j Z=3x2,...

Post as a guest

Earn Coins

Use power base of 100MVA to change to per unit Consider the transmission system in figure...

Bus A Bus B R1 TI ine 1 20% 80% line 2 T2 R2 110 kV 11 kV The fault is located at point F, which ...

QUESTION 4. A single-line diagram of a power system is shown in Figure Q3 below, where...

A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y...

Figure 1 Single line diagram b2 b3 b1 b4 grid Τι 13 A power system single line diagram is shown...

Add Answer to:
UUUUUUUse scriere. 10) 33 Consider figure 3.1 below and answer the questions that follow Z=2j Z=3x2,...