Homework Answers
Add Answer to:
302. A solid shaft has the maximum allowable values shown: Shear Stress 14,000 PSI Normal Stress...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
Sup 3.2 A hollow aluminum allow [G 3.8 x 10* psi) shaft having a length of...
Sup 3.2 A hollow aluminum allow [G 3.8 x 10* psi) shaft having a length of 12 ft., an outside diameter of 4.50 in., and a wall thickness of 0.50 in. rotates at 3 Hz. The allowable shear stress is 6 ksi, and the allowable angle of twist is 5°. What horsepower may the shaft transmit?
3) The solid shaft is made of material that has an allowable shear stress of Tallow...
3) The solid shaft is made of material that has an allowable shear stress of Tallow 12 MPa. Determine the required diameter of the shaft to the nearest millimeter. Please draw a plot of the internal Torque along the length of the shaft. 15 N·m 25 N·m 30 N·m 60 N'm 70 N·m
The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of...
The solid aluminum shaft has a diameter of 50 mm and an
allowable shear stress of 60MPa. Determine the largest torque T1
that can be applied to the shaft if it is also subjected to other
torsional loadings.Also, determine the maximum shear stress within
regions CD and DE. I do not have access to G and E for aluminum, so
for now, assume G =28 GPa and E = 69 GPa.
Please show all your work.
Question 2: The shaft ABC shown in the figure is driven by a motor that delivers...
Question 2: The shaft ABC shown in the figure is driven by a motor that delivers 300kW at a rotational speed of 32 rev/sec. The gears at B and C take out 120k W and 180kW respectively. diameter of the shaft if the allowable shear stress is 50MPa, the allowable angle of twist between points A and C is 4° and G- 75GPa. of the two parts of the shaft are Li = 1.5m and L,-0.9m. Determine the required Motor...
Problem 2: A solid steel shaft ABC of 50 mm diameter is driven at A by...
Problem 2: A solid steel shaft ABC of 50 mm diameter is driven at A by a motor that transmits 50 kW to the shaft at 40 rpm. The gears at B and C drive require 35 and 15 kW, respectively. Calculate the maximum shear stress in the shaft and the angle of twist between A and C. G 80 GPa 10 marks Motor 50 mm
2. If the solid shaft is made from material having an allowable shear stress of Tallowable...
2. If the solid shaft is made from material having an allowable shear stress of Tallowable = 60 MPa, determine the required diameter of the shaft. 15 kN-m 30 kN m 75 kN-m 30 kN-m QUESTION 5 Problem 2: What is the maximum internal torque in the shaft? 45 kN-m 120 kN-m 25 kN-m 75 kN-m N QUESTION 6 Problem 2: What is the minimum diameter of the solid shaft? O 207 mm O 156 mm O 168 mm 132...
solve with explanasion please 1. The gear shaft shown below is a solid cylinder made of...
solve with explanasion please
1. The gear shaft shown below is a solid cylinder made of a material that has an allowable shear stress of 75 MPa and a shear modulus of 25 GPa. Calculate: 600 Nm a. The minimum shaft diameter (to nearest mm) required in sections AB and CD (10 pts) b. The resulting angle of twist of gear A relative to gear B (10 pts) 200 mm 900 Nm 500 Nm 200 mm 300 N·m SOON.m 200...
A solid bar of circular cross section has a diameter, d= 1.5 in., and length, L-54 shear modulus of elasticity, G11.5x 10spsi (see Figure 4). 4. in.. The da 1.5 in. L-54 in. Figure 4 (a) If a tor...
A solid bar of circular cross section has a diameter, d= 1.5 in., and length, L-54 shear modulus of elasticity, G11.5x 10spsi (see Figure 4). 4. in.. The da 1.5 in. L-54 in. Figure 4 (a) If a torque T 250 lb-ft is applied at the ends, find the values of maximum shear stress in the bar and the angle of twist between the ends of the bar. [10 marks] (b) If the allowable shear stress 6000 psi and the...
The gears attached to the fixed-end steel shaft are subjected to the torques shown in the figure. If the shear modulus of elasticity is 150 GPa a determine the following: nd the shaft has a d...
The gears attached to the fixed-end steel shaft are subjected to the torques shown in the figure. If the shear modulus of elasticity is 150 GPa a determine the following: nd the shaft has a diameter of 14 mm, a. Sketch the torque diagram along the steel shaft. b. Determine the maximum shear stress at Tmax and specify location. c. Sketch the shear stress distribution along the radial line at location specified in (b). d. Determine the displacement of the...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
Sup 3.2 A hollow aluminum allow [G 3.8 x 10* psi) shaft having a length of 12 ft., an outside diameter of 4.50 in., and a wall thickness of 0.50 in. rotates at 3 Hz. The allowable shear stress is 6 ksi, and the allowable angle of twist is 5°. What horsepower may the shaft transmit?
3) The solid shaft is made of material that has an allowable shear stress of Tallow 12 MPa. Determine the required diameter of the shaft to the nearest millimeter. Please draw a plot of the internal Torque along the length of the shaft. 15 N·m 25 N·m 30 N·m 60 N'm 70 N·m
The solid aluminum shaft has a diameter of 50 mm and an
allowable shear stress of 60MPa. Determine the largest torque T1
that can be applied to the shaft if it is also subjected to other
torsional loadings.Also, determine the maximum shear stress within
regions CD and DE. I do not have access to G and E for aluminum, so
for now, assume G =28 GPa and E = 69 GPa.
Please show all your work.
Question 2: The shaft ABC shown in the figure is driven by a motor that delivers 300kW at a rotational speed of 32 rev/sec. The gears at B and C take out 120k W and 180kW respectively. diameter of the shaft if the allowable shear stress is 50MPa, the allowable angle of twist between points A and C is 4° and G- 75GPa. of the two parts of the shaft are Li = 1.5m and L,-0.9m. Determine the required Motor...
Problem 2: A solid steel shaft ABC of 50 mm diameter is driven at A by a motor that transmits 50 kW to the shaft at 40 rpm. The gears at B and C drive require 35 and 15 kW, respectively. Calculate the maximum shear stress in the shaft and the angle of twist between A and C. G 80 GPa 10 marks Motor 50 mm
2. If the solid shaft is made from material having an allowable shear stress of Tallowable = 60 MPa, determine the required diameter of the shaft. 15 kN-m 30 kN m 75 kN-m 30 kN-m QUESTION 5 Problem 2: What is the maximum internal torque in the shaft? 45 kN-m 120 kN-m 25 kN-m 75 kN-m N QUESTION 6 Problem 2: What is the minimum diameter of the solid shaft? O 207 mm O 156 mm O 168 mm 132...
solve with explanasion please
1. The gear shaft shown below is a solid cylinder made of a material that has an allowable shear stress of 75 MPa and a shear modulus of 25 GPa. Calculate: 600 Nm a. The minimum shaft diameter (to nearest mm) required in sections AB and CD (10 pts) b. The resulting angle of twist of gear A relative to gear B (10 pts) 200 mm 900 Nm 500 Nm 200 mm 300 N·m SOON.m 200...
A solid bar of circular cross section has a diameter, d= 1.5 in., and length, L-54 shear modulus of elasticity, G11.5x 10spsi (see Figure 4). 4. in.. The da 1.5 in. L-54 in. Figure 4 (a) If a torque T 250 lb-ft is applied at the ends, find the values of maximum shear stress in the bar and the angle of twist between the ends of the bar. [10 marks] (b) If the allowable shear stress 6000 psi and the...
The gears attached to the fixed-end steel shaft are subjected to the torques shown in the figure. If the shear modulus of elasticity is 150 GPa a determine the following: nd the shaft has a diameter of 14 mm, a. Sketch the torque diagram along the steel shaft. b. Determine the maximum shear stress at Tmax and specify location. c. Sketch the shear stress distribution along the radial line at location specified in (b). d. Determine the displacement of the...
Most questions answered within 3 hours.
-
HBR Article: How to Act Quickly Without Sacrificing Critical
Thinking
Read the attached Harvard Business Review...
asked 2 minutes ago -
if
we have a large voluntary respond sample consistings of weights of
subject who choose to...
asked 4 minutes ago -
consider a simple economy that prodices only pens the
following contains information on the economys money...
asked 16 minutes ago -
calculate the mass of magnesium metal that must be reacted with
hydrochloric acid to produce 1.00...
asked 21 minutes ago -
On a can of sardines it is written that the can contains 10
sardines. You open...
asked 35 minutes ago -
Eminent domain is the right of government to acquire private
land, without the owner’s consent, for...
asked 42 minutes ago -
3. A two-workstation cell uses a kanban system to produce
200,000 parts per year. Expected leadtime...
asked 50 minutes ago -
Let Y1,…, Y18 be a random sample from a uniform distribution on
the interval (0, θ],...
asked 55 minutes ago -
Two charges q1 = −3.20 nC and q2 = +8.42 nC are at a distance of...
asked 57 minutes ago -
in
a survey of 1433 people,909 people said they voted in a recent
presidential election.Voting records...
asked 57 minutes ago -
The factor of incentive scheme fail is because of rewards
rupture relationships. Explains
(in 300 words)
asked 1 hour ago -
Given an operating system that supports a one-to-one
relationship between user-level threads and kernel-level threads
and...
asked 1 hour ago