Machine Design
With reference to the following figure, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.
a) 11mm
b) 9mm
c) 8mm
d) 7mm
Homework Answers
Answer: a
Explanation: 0.707hl₁σ+1.414hl₂τ=20000 or 0.707x10x50x40+1.414x10xl₂x40=20000.
1. For the following nominal sizes of fillet welds determine: a) The throat thickness b) The...
1. For the following nominal sizes of fillet welds determine: a) The throat thickness b) The safe load (N/mm), weld material = 410MP and FoS=3. Nominal size (mm) 4681012 1620 24 Throat thickness (mm) Safe load (N/mm) Note: These results can be used to solve the remainder of problems. Answer N/mm mm |2.8 387 4.2 580 5.7 773 7.1 966 8.5 1160 11.3 1550 14.1 1930 17.02320 2. A 100mm wide and 10mm thick steel strap is to be welded...
Two steel plates, each ¼ inch thick, are to be joined by two fillet welds. If...
Two steel plates, each ¼ inch thick, are to be joined by two fillet welds. If the joint is to withstand a load of 50,000 lb and an E7014 electrode (allowable tensile strength – 21,000 psi) is used, determine the length of weld at each edge. If the plate width is 10 inches, how would you distribute the weld? Draw a sketch.
Machine Design
A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².a) None of the listedb) 11.21mmc) 12.33mmd) 14.12mm
As shown in Figure 8, the structural member (beam) is 7m long, carries a 2 kN point load, a 1.2 kN/m uniformly distribu...
As shown in Figure 8, the structural member (beam) is 7m long, carries a 2 kN point load, a 1.2 kN/m uniformly distributed load and is supported at points A and B. The beam is constructed from two pieces of steel plate (2 at 80mm x 8mm) that are welded together with 3mm welds. Section properties for the beam are also listed. Given the support reactions as RAv 5.8 kN and RBv 2.2 kN, as well as the shear force...
4. (a) Design a bolted joint to join the two members shown in the figure below. Specify the number of bolts, the pattern, the bolt grade, and the bolt size 8 x4 x 12 Box sect 4 in 6in 0.50 in ty...
4. (a) Design a bolted joint to join the two members shown in the figure below. Specify the number of bolts, the pattern, the bolt grade, and the bolt size 8 x4 x 12 Box sect 4 in 6in 0.50 in typical 0.50 plate 12 000 lb P (b). Two steel plates are joined using 3/8-inch parallel-loaded fillet welds. The yield strength, Sy, and the length of the welds are known. The design factor is 3.5. Determine the maximum tensile...
Question 1 (30 Marks) Plate A is fillet-welded to Plate B as shown in Figure 1. Plate A and Plate B have the same material properties Both plates are 10 mm thick. There are two holes (with a diameter...
Question 1 (30 Marks) Plate A is fillet-welded to Plate B as shown in Figure 1. Plate A and Plate B have the same material properties Both plates are 10 mm thick. There are two holes (with a diameter of d) in Plate A. It is assumed that weld failure will not occur (a) If Plate A has a yield stress (fy) of 350 MPa and an ultimate tensile strength (fu) of 450 MPa, what is the maximum load (P)...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
Question 1 A turning operation is carried out on aluminum. Based on the specific energy values...
Question 1 A turning operation is carried out on aluminum. Based on the specific energy values in Table 20.2, determine material removal rate and cutting power in the operation under the following sets of cutting conditions: (a) Cutting speed 5.6 m/s, feed 0.25 mm/rev, and depth of cut 2.0 mm; and (b) cutting speed- 1.3 m/s, feed 0.75 mm/rev, and depth 4.0 mm. Question 2 Consider a turning operation performed on steel whose hardness 225 HB at a cutting speed...
need solution for milestones A Q1 Solid Mechanics 3 Assessment Task 1a - 2020 Milestone a...
need solution for milestones A Q1
Solid Mechanics 3 Assessment Task 1a - 2020 Milestone a Question 1. For each of the plane-stress conditions given below, construct a Mohr's circle of stress, find the principal stresses and the orientation of the principal axes relative to the xy axes and determine the stresses on an element, rotated in the x-y plane 60° counterclockwise from its original position: (a) dx = 200 MPa Oy - 300 MPa T .40 MPa (b) dx...
Auge Steel Framing Details 1. Complete all light g auge steel componente ir the following wall se...
auge Steel Framing Details 1. Complete all light g auge steel componente ir the following wall section, including floor joists, wall studs, roof rafters, and required clips angles, stiffeners, and fasteners. Label all components. Roof sheathing Wall sheathing 。 Interior wallboard Subflooring Foundation 103 Scale: l square =2" (50 mm) Name: necessity of cutting holes in m on the construction ste 12.11. 12.15). Thack etions a sed for top and bottom plates, e construction, shemperature that col tural shapes. Prers...
1. For the following nominal sizes of fillet welds determine: a) The throat thickness b) The safe load (N/mm), weld material = 410MP and FoS=3. Nominal size (mm) 4681012 1620 24 Throat thickness (mm) Safe load (N/mm) Note: These results can be used to solve the remainder of problems. Answer N/mm mm |2.8 387 4.2 580 5.7 773 7.1 966 8.5 1160 11.3 1550 14.1 1930 17.02320 2. A 100mm wide and 10mm thick steel strap is to be welded...
As shown in Figure 8, the structural member (beam) is 7m long, carries a 2 kN point load, a 1.2 kN/m uniformly distributed load and is supported at points A and B. The beam is constructed from two pieces of steel plate (2 at 80mm x 8mm) that are welded together with 3mm welds. Section properties for the beam are also listed. Given the support reactions as RAv 5.8 kN and RBv 2.2 kN, as well as the shear force...
4. (a) Design a bolted joint to join the two members shown in the figure below. Specify the number of bolts, the pattern, the bolt grade, and the bolt size 8 x4 x 12 Box sect 4 in 6in 0.50 in typical 0.50 plate 12 000 lb P (b). Two steel plates are joined using 3/8-inch parallel-loaded fillet welds. The yield strength, Sy, and the length of the welds are known. The design factor is 3.5. Determine the maximum tensile...
Question 1 (30 Marks) Plate A is fillet-welded to Plate B as shown in Figure 1. Plate A and Plate B have the same material properties Both plates are 10 mm thick. There are two holes (with a diameter of d) in Plate A. It is assumed that weld failure will not occur (a) If Plate A has a yield stress (fy) of 350 MPa and an ultimate tensile strength (fu) of 450 MPa, what is the maximum load (P)...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
Question 1 A turning operation is carried out on aluminum. Based on the specific energy values in Table 20.2, determine material removal rate and cutting power in the operation under the following sets of cutting conditions: (a) Cutting speed 5.6 m/s, feed 0.25 mm/rev, and depth of cut 2.0 mm; and (b) cutting speed- 1.3 m/s, feed 0.75 mm/rev, and depth 4.0 mm. Question 2 Consider a turning operation performed on steel whose hardness 225 HB at a cutting speed...
need solution for milestones A Q1
Solid Mechanics 3 Assessment Task 1a - 2020 Milestone a Question 1. For each of the plane-stress conditions given below, construct a Mohr's circle of stress, find the principal stresses and the orientation of the principal axes relative to the xy axes and determine the stresses on an element, rotated in the x-y plane 60° counterclockwise from its original position: (a) dx = 200 MPa Oy - 300 MPa T .40 MPa (b) dx...
auge Steel Framing Details 1. Complete all light g auge steel componente ir the following wall section, including floor joists, wall studs, roof rafters, and required clips angles, stiffeners, and fasteners. Label all components. Roof sheathing Wall sheathing 。 Interior wallboard Subflooring Foundation 103 Scale: l square =2" (50 mm) Name: necessity of cutting holes in m on the construction ste 12.11. 12.15). Thack etions a sed for top and bottom plates, e construction, shemperature that col tural shapes. Prers...
Most questions answered within 3 hours.
-
1. What is a “Bankster”? What is insider trading? Why is it
illegal?
2. What is...
asked 17 seconds from now -
Given:
Curent Assets: $600,000
Total Assets: $2,600,000
Current Liabilities: $500,000
Total Liabilities: $1,700,000
What is the...
asked 1 minute ago -
A transverse wave on a cord is given by
D(x,t)=0.18sin(2.7x−61.0t), where Dand x are in m...
asked 6 minutes ago -
ASSIGNMENT
ANSWER ANY TWO OF THE FOLLOWING IN 2-3 PARAGRAPHS OF EACH
QUESTION.
1: Where is...
asked 4 minutes ago -
Question 1 (5 marks)
Studies have shown that the price elasticity for GP
consultations is -0.2...
asked 6 minutes ago -
The owner of 22 restaurants was asked how he does marketing
research. He answered that he...
asked 10 minutes ago -
The premium on a June 17 British pound call option with a strike
price of $1.2560...
asked 26 minutes ago -
We sometimes have to choose between the highest NPV and IRR;
will we not always get...
asked 21 minutes ago -
How do ethical issues affect decision making and what ethical
issues do you see in the...
asked 24 minutes ago -
Calculate the moment
of inertia (in kg·m2) of a skater given the following
information.
(a)
The...
asked 39 minutes ago -
A small body of mass m performs small oscillations sliding (no
rolling) along the bottom of...
asked 43 minutes ago -
The electric field in the region between two oppositely charged,
parallel, conducting plates has a magnitude...
asked 42 minutes ago