Homework Answers
-The above circuit is gated D latch
Which has just two inputs DATA and ENABLE (CLOCK)
-when HIGH is received at ENABLE point, the DATA is copied to the output.Even if ENABLE input then goes low, the output remains unchanged.
The DATA input is set and reset connected through inverter.
Final output is completely opposite to each other.
The ENABLE pin enables the operation of set and reset pins.
Add Answer to:
What is the function of the following circuit? os TDD (Data) Clk A. Falling Edge Triggered...
Q D Clock Clk Q Clock Qb Q Qa Q Q Multiple type of flip-flops Circuit...
Q D Clock Clk Q Clock Qb Q Qa Q Q Multiple type of flip-flops Circuit The figure above shows a circuit that use three different types of D flip-flops: a) D latch b) Rising-edge D flip-flop c) Falling-edge flip-flop For each one of the flip-flops enter their output for the times t1.t2.t3.t4 Assume that initially all outputs are '0' D
a) (5 marks) Explain the difference between a latch, a gated latch and a flip flop....
a) (5 marks) Explain the difference between a latch, a gated latch and a flip flop. b) (5 marks) A gated SR latch has the following schematic diagram CLK a) Draw a timing diagram showing the Q and Q outputs for the following sequence of inputs: CLK R Assume that the initial state of the outputs is Q 0 and Q 1 c) (5 marks) Draw a schematic diagram for a rising edge-triggered master-slave D flip- flop built using two...
Design a double edge-triggered D flip-flop using multiplexers only. The output of the flip-flop Q should...
Design a double edge-triggered D flip-flop using multiplexers only. The output of the flip-flop Q should “sample” the value of the input D on both rising (+ve) and falling (-ve) edges of the clock CLK. Provide detailed solution and explanation.
Design a double edge-triggered D flip-flop. The output of the flip-flop Q should "sample" the value...
Design a double edge-triggered D flip-flop. The output of the flip-flop Q should "sample" the value of the input D on both rising (+ve) and falling (-ve) edges of the clock CLK. Design an FSM counter that counts the sequence: 00, 11, 01, 10,00, 11, ..
5) Complete the timing diagram for the circuit with one positive-edge and one negative-edge triggered D...
5) Complete the timing diagram for the circuit with one positive-edge and one negative-edge triggered D FF. Q1 and Q0 start a low (0) because CLRn starts low. CLk K - 1 cun Q ई 6) For each set of waveforms, create a D, T or J/K waveform that will generate the desired Q output. Assume Q starts low. There are several right answers for the J and K inputs. To prevent flip-flop instability, all changes to the D, T...
1. Write the Boolean expression for each output from the PLA below: F = F G...
1. Write the Boolean expression for each output from the PLA below: F = F G H 2. Draw the block diagram (not logic gates) and the truth table for a 4-1 multiplexer. Label all inputs, outputs and select lines. 3. Explain the problem with the S-R latch and how it is fixed by the J-K flip-flop 4. Write the truth table for a Gated D Latch: 5. Complete the following timing diagram for the rising-edge-triggered D flip-flop: akrrrr G1
3. Answer the following questions about a data flip-flop (D-Flip Flop): a) (4 ps) Write the VHDL required to define a rising-edge triggered (RET) D-Flip Flop with additional clock enable (CEN) an...
3. Answer the following questions about a data flip-flop (D-Flip Flop): a) (4 ps) Write the VHDL required to define a rising-edge triggered (RET) D-Flip Flop with additional clock enable (CEN) and reset inputs. Your reset may be synchronous or asynchronous. Assume any input, output, or signal variables that you require have already been declared in VHDL (you do not have to write the declarations for these) b) [I pal ls your reset syachronous or asynchronous for the D-Flip Flop...
1. Design a combinational circuit that coverts a 4-bit Gray code to a 4-bit Excess-3 code....
1. Design a combinational circuit that coverts a 4-bit Gray code to a 4-bit Excess-3 code. Provide detailed solution and explanation 2. Design a double edge-triggered D flip-flop using multiplexers only. The output of the flip-flop Q should "sample" the value of the input D on both rising (+ve) and falling -ve) edges of the clock CLK. Provide detailed solution and explanation 3. Design an FSM counter that counts the sequence: 00, 11, 01, 10, 00, 11, Provide detailed solution...
Done 01. When an inverter is placed between both inputs of an SR. flip-lop, the resulting flip-fo...
digital system solve Q3andQ4
Done 01. When an inverter is placed between both inputs of an SR. flip-lop, the resulting flip-fop is a (a) JK flip-flop (b) T flip-lop (c) Master Slave JK flip-flop (d) D flip-flop 02. A D flip-flop utilizing a Positive-Giate-Triggered (PGT) Clock is in the CLEAR" stae Which of the following input actions will cause it to change states? NGT stands for Negative-Gate-Triggered (a) CLOCK-NGT, D-O (b) CLOCK-PGT, D- (c) CLOCK- NGT: D- (d) CLOCK- PGT,...
Answers are at the end of the chapter 1. If an S-R latch has a 1...
Answers are at the end of the chapter 1. If an S-R latch has a 1 on the S input and a 0 on the R input and then the S input goes to 0, the latch will be (a) set (b) reset (c) invalid (d) clear 2. The invalid state of an S-R latch occurs when (c) S 1,R-1 (d) S-0, R-O 3. For a gated D latch, the output always equals the D input (a) before the enable...
Q D Clock Clk Q Clock Qb Q Qa Q Q Multiple type of flip-flops Circuit The figure above shows a circuit that use three different types of D flip-flops: a) D latch b) Rising-edge D flip-flop c) Falling-edge flip-flop For each one of the flip-flops enter their output for the times t1.t2.t3.t4 Assume that initially all outputs are '0' D
a) (5 marks) Explain the difference between a latch, a gated latch and a flip flop. b) (5 marks) A gated SR latch has the following schematic diagram CLK a) Draw a timing diagram showing the Q and Q outputs for the following sequence of inputs: CLK R Assume that the initial state of the outputs is Q 0 and Q 1 c) (5 marks) Draw a schematic diagram for a rising edge-triggered master-slave D flip- flop built using two...
Design a double edge-triggered D flip-flop. The output of the flip-flop Q should "sample" the value of the input D on both rising (+ve) and falling (-ve) edges of the clock CLK. Design an FSM counter that counts the sequence: 00, 11, 01, 10,00, 11, ..
5) Complete the timing diagram for the circuit with one positive-edge and one negative-edge triggered D FF. Q1 and Q0 start a low (0) because CLRn starts low. CLk K - 1 cun Q ई 6) For each set of waveforms, create a D, T or J/K waveform that will generate the desired Q output. Assume Q starts low. There are several right answers for the J and K inputs. To prevent flip-flop instability, all changes to the D, T...
1. Write the Boolean expression for each output from the PLA below: F = F G H 2. Draw the block diagram (not logic gates) and the truth table for a 4-1 multiplexer. Label all inputs, outputs and select lines. 3. Explain the problem with the S-R latch and how it is fixed by the J-K flip-flop 4. Write the truth table for a Gated D Latch: 5. Complete the following timing diagram for the rising-edge-triggered D flip-flop: akrrrr G1
3. Answer the following questions about a data flip-flop (D-Flip Flop): a) (4 ps) Write the VHDL required to define a rising-edge triggered (RET) D-Flip Flop with additional clock enable (CEN) and reset inputs. Your reset may be synchronous or asynchronous. Assume any input, output, or signal variables that you require have already been declared in VHDL (you do not have to write the declarations for these) b) [I pal ls your reset syachronous or asynchronous for the D-Flip Flop...
1. Design a combinational circuit that coverts a 4-bit Gray code to a 4-bit Excess-3 code. Provide detailed solution and explanation 2. Design a double edge-triggered D flip-flop using multiplexers only. The output of the flip-flop Q should "sample" the value of the input D on both rising (+ve) and falling -ve) edges of the clock CLK. Provide detailed solution and explanation 3. Design an FSM counter that counts the sequence: 00, 11, 01, 10, 00, 11, Provide detailed solution...
digital system solve Q3andQ4
Done 01. When an inverter is placed between both inputs of an SR. flip-lop, the resulting flip-fop is a (a) JK flip-flop (b) T flip-lop (c) Master Slave JK flip-flop (d) D flip-flop 02. A D flip-flop utilizing a Positive-Giate-Triggered (PGT) Clock is in the CLEAR" stae Which of the following input actions will cause it to change states? NGT stands for Negative-Gate-Triggered (a) CLOCK-NGT, D-O (b) CLOCK-PGT, D- (c) CLOCK- NGT: D- (d) CLOCK- PGT,...
Answers are at the end of the chapter 1. If an S-R latch has a 1 on the S input and a 0 on the R input and then the S input goes to 0, the latch will be (a) set (b) reset (c) invalid (d) clear 2. The invalid state of an S-R latch occurs when (c) S 1,R-1 (d) S-0, R-O 3. For a gated D latch, the output always equals the D input (a) before the enable...
Most questions answered within 3 hours.
-
QUESTION 1 Tamiflu is a drug used to treat influenza. A study
found that Tamiflu reduced...
asked 58 seconds from now -
Which of the following would be less likely to be used to
allocate factory overhead when...
asked 4 minutes ago -
Transverse pulses travel with a speed of 195 m/s along a taut
copper wire whose diameter...
asked 3 minutes ago -
Sampling for Engineers Homework question 11.51
Suppose that Y1;Y2;Y3;Y4 denote a random sample from a
Poisson(θ)...
asked 6 minutes ago -
Which of the following is cleaved by regulated intramembrane
proteolysis (RIP)? Select any/all answers that apply....
asked 6 minutes ago -
Random characters You decide to create a program characters.py
that fills a two-dimensional list with random...
asked 18 minutes ago -
What are the major sources of error in your determination of the
molar mass? Select all...
asked 22 minutes ago -
A. Suppose your manager indicates that for a normally
distributed data set you are analyzing, your...
asked 43 minutes ago -
During the month of August, the average temperature of a lake
next to a local college...
asked 25 minutes ago -
Which of these four researchers is most likely to have made Type
1 error
Kim who...
asked 39 minutes ago -
In a performance test, each of two cars takes 8.9 s to
accelerate from rest to...
asked 39 minutes ago -
Sapphire Aerospace operates 52 weeks per year, and its cost of
goods sold last year was...
asked 43 minutes ago