Calculate the force a punch press must excert if it is to punch out a large...
Calculate the force a punch press must excert if it is to punch out a large washer from a strip of 1/4 inch thick sheet steel with an ultimate shear stress of 60 ksi. The washer dimensions are as follows: inside/hole diameter is 1 inch thick and the outside diameter is 2 inches.
Homework Answers
Do let me know if you understood the steps
by giving me a thumbs up.
Thanks and keep Chegging.
Add Answer to:
Calculate the force a punch press must excert if it is to punch
out a large...
Rectangular parts are being stamped out of Xinch steel plate. (Out = 58,000 psi and Tuft...
Rectangular parts are being stamped out of Xinch steel plate. (Out = 58,000 psi and Tuft = 30,000 psi) Problem #9: What is the shear area? Problem #10: How much shear force is needed by the punch press? .25 inch thick 3 inch 4 inch Force
Please show work. Thank you! A punch press has punches forty (40) circles that are 2...
Please show work. Thank
you!
A punch press has punches forty (40) circles that are 2 inches in diameter through medium carbon steel that is 0.125" thick. If six hydraulic cylinders are used to achieve this force, what diameter cylinders are required if the pump has a maximum continuous operating pressure of 3150 psi? Sheaf Strcho th 2.
A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made...
A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degrees over the 36 inches length. The inside diameter of the shaft is 0.65 that of the outside diameter of the shaft. Determine: a) the required inside and outside diameter of the shaft based on...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP...
6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP at 1250 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 Inche length. The inside diameter of the shaft is 0.8 that of the outside diameter of the shaft. Determine: a) the required inside and...
Question 8. Section 2-3 Shear Stresses 6. In the bolted connection of Fig. 2-8, assume that...
Question 8.
Section 2-3 Shear Stresses 6. In the bolted connection of Fig. 2-8, assume that the bolts are , in. in diameter and that the allowable shear stress for the bolts is 14,500 psi. Based on bolt shear only, compute the safe allowable load P that may be applied 7. Compute the force required to punch a 1 in. diameter hole through a ½ in, thick boiler plate. The ultimate shear strength for the material is 42,000 psi. 8....
A solid shaft 32 inches long must carry a torque of 5600 lb-in. The shaft is...
A solid shaft 32 inches long must carry a torque of 5600 lb-in. The shaft is made out of aluminum. Aluminum shafts come in increments of 1/16th inch increments between diameter of 0.25 and 2.5 inches. Determine: a) the required size and cost of an aluminum shaft based on the below design criteria. Allow Shear Stress (ksi) Allow Angle of Twist (deg.) Density (lb/ft3) Cost per Pound ($) Modulus of Rigidity (ksi) Aluminum 18 4.5 169 0.75 4000 Design...
5 Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a...
5 Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a torque of 3600 lb-in. The shaft is made out of aluminum. Aluminum Shafts come in increments of 1/16th inch increments between diameter of 0.25 and 2.5 inches. Determine: a) the required size and cost of an aluminum shaft based on the below design criteria. 02:55:27 Allow Shear Stress (ksi) Allow Angle of Density Cost per Modulus of Pound Rigidity ($) (ksi) Twist (deg.) Kib/A3)...
mechanical engg
A helical-coil compression spring is to be designed to exert a static force of 100 lb when the spring is compressed 2.0 inches. The spring must fit inside a cylindrical hole. The following information is given for your calculation. Spring index, C Clearance between the spring and the hole Diameter of the hole, dhole Fractional overrun to closure, ? 10 0.25 inch 2.25 inches 0.15 The spring is made of music wire A228 with m = 0.145 and A =201...
Assume that if the shear stress in steel exceeds about 4.0o x 108 N/m2, the steel...
Assume that if the shear stress in steel exceeds about 4.0o x 108 N/m2, the steel ruptures. (a) Determine the shearing force necessary to shear a steel bolt 1.45 cm in diameter. (b) Determine the shearing force necessary to punch a 1.05-cm-diameter hole in a steel plate 0.800 cm thick. Step 1 (a) we know that force F is equal to the surface area A times stress σ so we have 4 108 N/m 2 Your response differs from the...
Rectangular parts are being stamped out of Xinch steel plate. (Out = 58,000 psi and Tuft = 30,000 psi) Problem #9: What is the shear area? Problem #10: How much shear force is needed by the punch press? .25 inch thick 3 inch 4 inch Force
Please show work. Thank
you!
A punch press has punches forty (40) circles that are 2 inches in diameter through medium carbon steel that is 0.125" thick. If six hydraulic cylinders are used to achieve this force, what diameter cylinders are required if the pump has a maximum continuous operating pressure of 3150 psi? Sheaf Strcho th 2.
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP at 1250 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 Inche length. The inside diameter of the shaft is 0.8 that of the outside diameter of the shaft. Determine: a) the required inside and...
Question 8.
Section 2-3 Shear Stresses 6. In the bolted connection of Fig. 2-8, assume that the bolts are , in. in diameter and that the allowable shear stress for the bolts is 14,500 psi. Based on bolt shear only, compute the safe allowable load P that may be applied 7. Compute the force required to punch a 1 in. diameter hole through a ½ in, thick boiler plate. The ultimate shear strength for the material is 42,000 psi. 8....
5 Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a torque of 3600 lb-in. The shaft is made out of aluminum. Aluminum Shafts come in increments of 1/16th inch increments between diameter of 0.25 and 2.5 inches. Determine: a) the required size and cost of an aluminum shaft based on the below design criteria. 02:55:27 Allow Shear Stress (ksi) Allow Angle of Density Cost per Modulus of Pound Rigidity ($) (ksi) Twist (deg.) Kib/A3)...
Assume that if the shear stress in steel exceeds about 4.0o x 108 N/m2, the steel ruptures. (a) Determine the shearing force necessary to shear a steel bolt 1.45 cm in diameter. (b) Determine the shearing force necessary to punch a 1.05-cm-diameter hole in a steel plate 0.800 cm thick. Step 1 (a) we know that force F is equal to the surface area A times stress σ so we have 4 108 N/m 2 Your response differs from the...
Most questions answered within 3 hours.
-
Why are polymers not typically casted into products?
asked 14 minutes ago -
When rolling a die 129 times, what is the probability of rolling
a 6 no more...
asked 31 minutes ago -
4. A call option currently sells for $7.75. It has a strike
price of $85 and...
asked 19 minutes ago -
1.
You need to prepare 10.0 liters of an acid aqueous solution with a
pH of...
asked 22 minutes ago -
Along an aggregate supply curve, if the level of output is less
than the natural level...
asked 23 minutes ago -
By 2025, annual consumption in emerging markets will total $30
trillion and contribute more than ________...
asked 28 minutes ago -
At what point does reformation cease to be a viable option for
those who are oppressed...
asked 32 minutes ago -
Place letters corresponding to amounts in the proper order for
lightest to heaviest samples:
a) 2100...
asked 36 minutes ago -
Consider the multicore processor with 6 heterogeneous cores
labelled C1, C2, C3, C4, C5, and C6....
asked 39 minutes ago -
Document system components according to standards and procedures
(Implement and hand over system components) IT administrative
asked 39 minutes ago -
The college asked 700 students if they wanted a longer spring
break and 600 students said...
asked 39 minutes ago -
Determine the temperature (in Celsius) at which 1.00 mole of an
ideal gas will have a...
asked 1 hour ago