Why can you not have large TTL fan-out from the output of a CMOS device?
Solution -first of all we have to know what is the TTL fan- out and CMOS device
TTL faimly - the ttl faimly was the most widely used logic faimy for several year chareacterised by its relitivity high speed operation ,it has now been largely repaced by cmos logic the physical represntation of tge binary logic states in these faimilies are high and low voltage.
TTL CHARACTERISTICS - each logic faimly is characterised by several important parameter these properties and how the reletated to the TTL logic faimly.
FAN-OUT - fan-out specifies the no. of statndered loads that the output of the gate can drive without impairing of its noramal operation.
due to the nature of TTL gate, two different fanout values are given , one for high outpit and one for low output.
CMOS FAIMLY - cmos ogic is examlified by its extremely low poer conspution and high noise immunity,
hence its prevalently used in device demanding low power dissipation such as digital wristwatches and other bettery power device or in devie oprate in noisy envionrment such as industrial plant.
A wide variety of CMOS logic devicein the 4000 series are available
CMOS CHARACTERSTICS
The voltage transfer curve for a typically CMOS logic gate, the curve in the transition region are almost vertical this narrow transition region is reason for CMOS logic high noise immunity, not much voltage range is covered in th etransition form one state to other. to conrtast to TTL device the thjresold voltage depends on the supply voltage.
The main reason we dont used the large TTL fan out from the output of CMOS device
-The fan out of CMOS device is usually graeter than 50 beacouse the input current requirment of CMOS logic is nil (pA). however, current is requird to charge discharge the capacitance of CMOS inputs during logic transition.hence the greater the fan out the longer the propagation dealy.
e.g. with VDD=5V, the propagation delay will increased from 60nsec when the out drive 1 input to 50nsec whrn the output drive 10 inputs. as rule of thumb you can assume the load will be 5 pf per CMOS input 5 to 15 pf for stay wiring capacitance.
outputs of cmos gates like those of totem-pole TTL gate , should never be connected togather also, the power supply should be turned on before applying any logic signal to CMOS device and the logic signal should be removed before turning off the supplly , other wise the device could be damaged.
Why can you not have large TTL fan-out from the output of a CMOS device?
2. Design a digital logic circuit to convert part of the output code from part 1. to a binary signal. Use CMOS gates. (hint, the simpler you can get the logic, the less work you will have). You must draw the circuit with transistors In Out DUIi 0111 011 0011 010 0001 001 2. Design a digital logic circuit to convert part of the output code from part 1. to a binary signal. Use CMOS gates. (hint, the simpler you...
The CMOS inverter can be used as an amplifier because of the switching characteristics (see the figure on the right.) a) (2pts) Determine the gain of this very high gain for small signals Out amplifier Vin (V b) (lpt) Determine the phase difference between the input and output 1M R2 V2 U1A 0/500mV C1 .1uF 100k4069 c) (lpt) Determine the dc level of voltage at the inverter input 1kHz out d) (lpt) Explain why it is this particular value The...
Have you ever used a wearable device that tracked your calories? (Fitbit is a popular example.) If so, describe the device and what it claimed to track. If not, select a device and describe it. Using concepts from the videos, explain why this device may lack accuracy. If you have used a device before, have you noticed any obvious inaccuracies? Explain. Do you think there is a psychological value in seeing calories burned, even if the number is incorrect? Explain...
4. A CMOS port output is modelled as shown in Figure 3.4(b). It is powered from 5V. The value of RS(high) is estimated to be 120 U and the value of RS(low) 70 U. One port pin will light an LED when it is at Logic 1, and another will light an LED when it is at Logic 0. An LED current of 4 mA is required; for this the LEDs have a forward voltage of 1.8 V. Sketch a...
2. Explain why restaurants that have all you can eat buffets do not go out of business. In your answer explain it using the idea of consumer satisfaction and marginal utility.
A metal-encased medical device such as an ECG machine can be powered either from a wellgrounded perfectly insulated 120V AC power source, or from a battery. Which power source you recommend, and why?
3. You have bought a data acquisition device from Ebay. The sampling interval of the device is 1 msec. a. What is the sampling frequency of the device? What is the folding frequency of the device? Now, you are measuring following sinusoidal signals with the data acquisition device. For each signal, draw 1) Fourier transform magnitude of the original continuous-time signal, 2) Fourier transform magnitude of the sampled signal (draw at least first positive replica and first negative replica), 3)...
in large programs, it can be helpful to have a function specificaly for printing out an error message to the user or to a log when an exception (an error) has occurred Generally speaking, errors are tracked through unique error codes, making it easy for the programmer to implement. Assume you are given the task to implement a function for manager wants you to implement a basic function for now to check the functionality Implement a function called displayError, with...
Calculate the static logic high fan-out for the circuit of Figure 5.3, assuming that VOH Of the driving gate can drop from-0.7 V to 0.8 V. Use β = 50. CC 0 c300 300 Ω RCI 270 Ω 04 CI 03 E4 CIA ds o E4 RE 1.24 kΩ VEE -5.2 V ) Circuit b Logic Symbol Calculate the static logic high fan-out for the circuit of Figure 5.3, assuming that VOH Of the driving gate can drop from-0.7 V...
You have a device that needs a voltage reference of 3.0 V, but you have only a 9.0 V battery. Fortunately, you also have several 10 k? resistors.Choose the circuit that shows how you can use the resistors and the battery to make a circuit that provides a potential difference of 3.0 V.