A comparison between the Cp and Cpk for a process would find which of the following to be true?
A comparison between the Cp and Cpk for a process would find which of the following...
Question: The following is true about process capability: O A A high Cp, a lw Cpk tells you that the process is capable, but off-center O B The Cpk is always greater than the Cp O C Cpk is the same as Ppk O D Cpk has no bearing on expected defects per million opportunities
Q1: choose the correct answer: - 6σ < C_p means that the process is capable regardless if it is centered or not? A) Yes B) No - Data are usually discrete and in the form of counts are called variables. A) Yes B) No - The control chart is an _____________ process monitoring technique widely used to eliminate process variability A) on-line B) off-line C) both a and b D) out of control - C control chart is used with...
Given that the customer requirements for the process is (11.9, 12.1), using X bar and R chart, find Cp, Cpk and DPMO for the following samples (there are 16 samples). Assume the process is normally distributed. Given that the customer requirements for the processis (11.9, 12.1), using X bar and R chart, find Cp, Cpk and DPMO for the following samples (there are 16 samples). Assume the process is ormally distributed. 1 Subgroup 111.945 2 12.03 3 12.01 4 11.97...
Which of the following is not true of Tukey's Multiple Comparison Method? a. It is based on the studentized range statistic q to obtain the critical value needed to construct individual confidence intervals. b. It requires that all sample sizes are equal, or at least similar. c. It can be employed instead of the analysis of variance. d. All of these. e. None of these.
A certain process is under statistical control and has a mean value of 130 and a standard deviation of 8. The specifications for the process are: a. USL (upper specification limit) = 150 b. LSL(lower specification limit) =100 a. Calculate the cp and cpk b. Which of these indices is a better measure of process capability and why? c. Assuminng a normal distribution what percentage of output is expected to fall ourside the specification. Why is it important to know...
20. Suppose a worker receives a 3% pay raise for the coming year, under which of the following will the purchasing power of the worker's wage rise? a. The rate of inflation in the coming year is below 3%. b. The rate of inflation in the coming year is 390. C. The rate of inflation in the coming year is above 390. d. All of these are correct. 21. Does the stabilization policy conducted by the government work? No, output...
Which of the following is an advantage of a structured interview? a. It facilitates comparison between applicants since all applicants are asked the same questions. b. It allows an interviewer to probe into missing information uncovered during the unstructured portion of the interview. c. It does not require the preparation of questions before the interview takes place. d. It allows an interviewer to ask any question, including non-job-related questions.
The budgeting process does not involve which of the following activities? a. Execution of plans to achieve goals. b. Specific goals are established. c. Periodic comparison of actual results to goals. d. Increase in sales by increasing marketing efforts.
Process Capablity Sixpack Report for Suppa 1. The process for supplier 2 is operaing under a. Common cause b Special cause c Both common and special cause d Neither special or common cause 2. Wthin variation is basicaly a. An estimate of the shor-tem varation caloulating an average range b. An estimate of the long-lerm varation An estimate of the shor-em varaion caloulating an estimate for the standard deviation based on ranges of the samples d. An estimate of the...
1. Consider the Viterbi algorithm. Which of the following statements is/are true. if any? (i) It is an algorithmused for optimal thresholding (ii) It is an algorithm to find shortest paths in on a network (ii)It is an algorithm to detect lines in images (a) (i) (b) (ii) (c) (ii) (d) All of the above (e) None of the above 4. If we apply a binary opening to the same object twice using the same structuring element, the effect. if...