Please find thickness
h = pd/2t
for Design, h pd/2t
t pd / 2h as per hoop stress
Similarly as per longitudinal stress, t pd / 4L
Diameter, d = 2 in
Pressure (PSI) |
Hoop Stress (h ) (PSI) |
Hoop Stress Thickness (th) (in) |
Longitudinal Stress (L ) (PSI) |
Longitudinal Stress Thickness (tL) (in) |
500 | 6031.41 | 0.083 | 2897.54 | 0.086 |
1000 | 11426.44 | 0.088 | 5439.35 | 0.092 |
1500 | 17880.05 | 0.084 | 8525.21 | 0.088 |
1000 | 1948.34 | 0.513 | 5680.60 | 0.088 |
500 | 6100.34 | 0.082 | 2493.08 | 0.100 |
Average Thickness | 0.170 | 0.091 |
As per hoop stress, thickness t = 0.17 in
As per longitudinal stress, thickness t = 0.091
Hence Average Thickness, t =0.131 in
Pressure (PSI) Hoop Stress Thickness in. Longitudinal Stress Thickness in. 500 1000 1500 1000 500...
Consider a thick-walled cylinder of inner radius and outer radius and thickness t . This cylinder is subject to a centrifugal force () from its longitudinal axis. If we know the radial stress ,the hoop stress ,the hoop strain , the radial strain : where is the Poisson ration and is the radial displacement. How to compute the TOTAL POTENTIAL ENERGY |TPE| = ? N.B. : is the work done by external forces is the elastic internal potential energy We...
Multiple Choice The stress developed in a cylindrical pressure vessel along the longitudinal axis is: a. Double the stress developed along the hoop axis b. Equal to the stress developed along the hoop axis c. Half the stress developed along the hoop axis d. None of the above QUESTION 12 The stress developed in a cylindrical pressure vessel along the longitudinal axis is: a. Proportional to the thickness of the vessel wall b. Half the stress developed along the hoop...
Will RATE!!! Calculate the tensile stress hoop and longitudinal developed in the walls of a cylindrical pressure vessel. The inside diameter is 18 inch. The wall thickness is k inch.The vessel is subjected to an internal gage pressure of 300 psi and a simultaneous external axial tensile load of 50,000 lb. 4.A V-belt with a groove angle 40 has a max belt tension 150 lb on the tight side and 75 lb on the loose side. If the coefficient of...
please answer both the questions Question 2 A titanium tube 200mm diameter and 5mm wall thickness is subjected to an internal pressure of 13.5MPa. The tube contains a longitudinal crack along its full length. Assuming that the tube can be approximated by a single edge notched plate subjected to a tensile stress equal to the hoop stress in the tube determine the crack length to cause failure. You may assume that the material fracture toughness is 55 MPavm. Please provide...
Part A The tank of the air compressor subjected to an internal pressure of 96 psi . The internal diameter of the tank is 22 in., and the wall thickness is 0.25 in. (Figure 1) Determine the hoop stress acting at point A. Express your answer to three significant figures and include the appropriate units. Li HA ? 0,= Value Units Submit Request Answer Figure Part B 1 of 1 Determine the longitudinal stress acting at point A. Express your...
Pressure Vessels a) What is the hoop stress (tangential stress) for the pressure vessel shown in Figure 37 b) What is the Margin of Safety? (M.S.-[P.allow/P,actual)-1) (Use A basis values, L direction) c) At what pressure will the vessel fail? FIGURE 3 2.500 2.300 14 PSIA (ATM) 2000 PSIG P a pressure rinner radius t a wall thickness Material Aluminum 2024-13 (use material properties for sheet
Find the shear stress at A-A, B-B and C-C Given Neutral axis at 6.38 mm V= - 1300 N I = 23540 mm^4 thickness is 2mm 100 mm We were unable to transcribe this image 100 mm
A thin-wall aluminum pop can is subjected to an internal pressure of 100 psi. The diameter and the wall thickness of the can are 2.5 inch and 0.004 inch respectively. The Young's modulus and Poisson's ratio for aluminum are E = 10 x 10psi and V = 0.33, respectively. The axial stress the stress along the longitudinal direction) is closest to O 32000 psi O 16000 psi 40000 psi 8000 psi
A thin-wall aluminum pop can is subjected to an internal pressure of 100 psi. The diameter and the wall thickness of the can are 2.5 inch and 0.004 inch respectively. The Young's modulus and Poisson's ratio for aluminum are E = 10 x 10$psi and V = 0.33, respectively. The axial stress (the stress along the longitudinal direction) is closest to 40000 psi 8000 psi 32000 psi 16000 psi A thin-wall aluminum pop can is subjected to an internal pressure...
1000 psi 9. For stress conditions on the element shown, find the principal stresses and the plane on which the maximum principal stress acts. Use the analytical method (stress transformation equations). Draw the two principal stress 3000 psl 3000 psi 5000 psi elements and maximum shear element