If you found it useful please rate the solution.
Q.2: An angle is used as a simply supported beam, 48 in. long. The beam carries a 1.0-kip load at...
2. A 30 ft long simply supported beam supports a uniformly distributed load of 2 kips/ft over the entire span. The beam and cross section are shown below. Draw the shear and moment diagrams, find the neutral axis location, moment of inertia of the composite section, the maximum bending stress on the cross section. (40 points) 10" 2 k/ft 1-3" 30'-0"
14.54 A simply supported rectangular beam with a span of 6 ft has a concentrated load of 4.1 kip at midspan. Se- lect the lightest rectangular wood beam that can safely support the loads (neglect the weight of the beam). The allowable stress in bending is 1200 psi and in shear parallel to the grain 100 psi 14.54 A simply supported rectangular beam with a span of 6 ft has a concentrated load of 4.1 kip at midspan. Se- lect...
A 5-m-long simply supported timber beam carries two concentrated loads as shown dimensions of the beam are shown a) At section a-a e the magnitude of the shear stress in the beam at point H. -7748 KNIm in the beam at point K the beam, at any location within the 5-m span length. V occurs in the beam at any location within the 5-m span length.)diagr. the magnitude of the shear stress (b) At section a-a, (e) Determine the maximum...
A simply supported wood beam of rectangular cross section and span length 2 m carries a uniformly distributed load of intensity 9 = 1 kN/m as shown. Calculate the maximum bending stress and the maximum shear stress in the beam.
Figure Q3 shows a simply supported beam carrying a point load. The beam hasa rectangular hollow steel section as shown in Figure Q3. a. Calculate the second moment of area of the section about the horizontal (10 marks) centroidal axis. Calculate the maximum allowable value of the point load Wif the elastic bending (15 marks) b. stress in the beam is to be limited to 250 MPa. c. Calculate the maximum shear stress at q-q in the beam when the...
A Simply supported wood beam AB with span length Labm Carries trapezoidal distributed load of eatersita q=vikula at the best and and at the right end. calculate the maximum bending stress Tomax clue to the load of the beam has a rectangular sechan with width 6=150mm and 9/2 Cross height ho 850mm. a
Problem 7.5 of your textbook (Haldar & Mahadevan): A simply supported beam of span L 360 inches is loaded by a uniformly distributed load w kip/in. and a concentrated kip applied at the midspan. The maximum deflection of the beam at the midspan can be calculated as: mar- 384 EI 48 E A beam with El 63.51 x 106 kip-in.2 Is selected to carry the load. Both w and P are statistically independent RVs with mean values estimated to be...
1. A simply supported beam is 14-ft long and is braced only at the ends. A concentrated service live load of 55 kips is located at midspan of the beam. Determine whether a W14x53 is adequate for this beam? The steel is A992, use LRFD.
Please refer AISC 15th edition 3. A simply supported beam (W18x97) is 50-ft long and is restrained at the supports and at midspan. It carries a uniform dead load of 0.4 kips/ft plus beam weight, and a live load of 1.0 kips/ft. The steel is A992 and the method of analysis is LRFD. Determine if this shape and length is adequate to support this load. Also determine which controls: flexural strength or deflection. The limiting maximum live load deflection is...
A simply supported composite beam 3 m long carries a uniformly distributed load of intensity q= 30 kN/m (see figure). The beam is constructed of a wood member, 100 mm wide by 150 mm deep, and is reinforced on its lower side by a steel plate 8 mm thick and 100 mm wide. (a) Find the maximum bending stresses σw and σs, in the wood and steel, respectively, due to the uniform load if the moduli of elasticity are Ew =...