Adam (with the same machine) performs tasks 1 and 2. After running a setup on the machine, he performs task 1 on every unit in a batch. Then, he runs another setup on the same machine before performing task 2 on every unit in the batch. After that, either Brad or Chloe performs task 3 on the units. Finally, Dorothee does task 4. Tasks 3 and 4 are done by the workers only so they do not require any setups.
Note: If your answer not an integer, please round up to 2 decimals. flow (a) When the batch size is 20, the capacity of Adam is flow unit(s) per hour, the capacity of Brad & Chloe is unit(s) per hour, and the capacity of Dorothee is unit(s) per hour. The bottleneck is (b) If the demand rate is 5 units per hours, the batch size should be units. If the demand rate is 10 units per hours, the batch size units should be (c) it takes hours to produce a batch starting with an empty system.
Homework Answers
Add Answer to:
Adam (with the same machine) performs tasks 1 and 2. After running a setup on the...
Two-step Process Utilization: A two- used to finish a product: painting and drying. There are 5 workers and each one ta...
Two-step Process Utilization: A two- used to finish a product: painting and drying. There are 5 workers and each one takes an average of 60 minutes to paint each unit. Drying takes place in an oven that can hold up to 100 units and it takes 5 minutes to load each unit. Once all the units are loaded into the oven, it takes 6 hours to dry each load. Assume that the process is capacity constrained (so the demand rate...
Step 1 Step 2 Step 3 Setup: 30 minutes Setup: 50 minutes Run: 2 minutes Run:...
Step 1 Step 2 Step 3 Setup: 30 minutes Setup: 50 minutes Run: 2 minutes Run: 3 minutes Consider the following three-step process with setup times and task times: Setup: 40 minutes Run: 5 minutes Refer to the Three-Step Line with Batch Processing Diagram. Assume the batch size is 10. At each station, the worker sets up the machine, runs 10 units through the process, then sets up the machine for the next batch. At the beginning, the worker at...
Question #2 (15 Points) The result of a detailed study of setup procedure on a molding machine is...
only question 3
Question #2 (15 Points) The result of a detailed study of setup procedure on a molding machine is shown in Table 1 below. The setup involved removing an old die and installing a new one. Tahle I InternalTime Performed by External?(min) Step# Setup 1 Check in at operation, go to die storage 2 Transfer new die 3 Remove old die 10 Setup person 16 Setup person 20 Setup person 20 Setup persorn 30 Operator 24 Setup person...
Alpha Assemblies produces a wide variety of products in their central Nebraska facility. Many of these products fit with...
Alpha Assemblies produces a wide variety of products in their central Nebraska facility. Many of these products fit within a line of standard truck and trailer parts. Within this is a set of hitches that can be made in two sizes (1-1/4 and 2) and three strengths (light duty, medium duty, and heavy duty). All of the hitches in this line have "natural" finishes so no additional steps are necessary after they are cast. The machine used to cast these...
2. Consider the following batch flow process consisting of three process steps performed by three machines: Step 1 Step...
2. Consider the following batch flow process consisting of three process steps performed by three machines: Step 1 Step 3 Step 2 Processing time 1 minute/part Processing time 1.5 minute/part Processing time 2 minute/part Setup time No Setup No Setup 20 minutes Work is processed in batch at each step. Before a batch is processed at step 1, the machine has to be set up. During There are no inventory buffers between steps. a setup, the machine is unable to...
Gordon Company produces custom-made machine parts. A setup activity is required for the batches of parts...
Gordon Company produces custom-made machine parts. A setup activity is required for the batches of parts that it produces. Activity output is measured using setup hours. The value-added standard (SQ) for this activity is zero. On July 1, at the beginning of the fiscal year, 15 setup hours were allowed and used per batch. The standard wage rate for setup labor is $24 per setup hour. During the first quarter of the new fiscal year, the company is planning to...
PA 84 In the welding operations of a bicycle manufacturer... In the welding operations of a...
PA 84 In the welding operations of a bicycle manufacturer... In the welding operations of a bicycle manufacturer, a bike frame has a flow time of about 14.35 hours. The time in the welding operation is spent as follows: 3 hours waiting in front of the cutting machine for the batch to start, 2 hours waiting for the setup of the machine, 1 hour waiting that the other pieces of the batch go through cutting, 2 minute at the cutting...
5. Changeover of fixtures on a machine takes 35 minutes. Following the changeover, an aver- ed be...
5. Changeover of fixtures on a machine takes 35 minutes. Following the changeover, an aver- ed before the correct setting is achieved. For ch part the processing time is two minutes and the material cost is $1.50. The labor cost for a skilled setup person to do the changeover and adjustment is $15.50 per hour. The labor cost of the machine operator is $10.50 per hour. Currently, the part is produced in batches of 50 units. Suppose the setup procedure...
a) Setup Cost: b) Setup Time: Rick Wing has a repetitive manufacturing plant producing automobile steering...
a) Setup Cost:
b) Setup Time:
Rick Wing has a repetitive manufacturing plant producing automobile steering wheels. Use the following data to prepare for a reduced lot size. The firm uses a work year of 305 days. Setup labor cost $40.00 per hour Annual holding cost $16 per unit Daily production (8 hours) 800 units day Annual demand for steering wheels 36,600 (305 days x daily demand of 120 units) Desired lot size (2 hours of production) 0 - 200...
A process has two stages. In the first stage, a machine makes two components, call them type A and B. It takes 250 seco...
A process has two stages. In the first stage, a machine makes two components, call them type A and B. It takes 250 seconds to switch production between the component types. During that time no production occurs. When in production, each component (A or B) requires 0.6 seconds to be completed. In the second stage, the components, A and B, are assembled to make a final product, call it C. The assembly stage can combine the two components into 1...
Two-step Process Utilization: A two- used to finish a product: painting and drying. There are 5 workers and each one takes an average of 60 minutes to paint each unit. Drying takes place in an oven that can hold up to 100 units and it takes 5 minutes to load each unit. Once all the units are loaded into the oven, it takes 6 hours to dry each load. Assume that the process is capacity constrained (so the demand rate...
Step 1 Step 2 Step 3 Setup: 30 minutes Setup: 50 minutes Run: 2 minutes Run: 3 minutes Consider the following three-step process with setup times and task times: Setup: 40 minutes Run: 5 minutes Refer to the Three-Step Line with Batch Processing Diagram. Assume the batch size is 10. At each station, the worker sets up the machine, runs 10 units through the process, then sets up the machine for the next batch. At the beginning, the worker at...
only question 3
Question #2 (15 Points) The result of a detailed study of setup procedure on a molding machine is shown in Table 1 below. The setup involved removing an old die and installing a new one. Tahle I InternalTime Performed by External?(min) Step# Setup 1 Check in at operation, go to die storage 2 Transfer new die 3 Remove old die 10 Setup person 16 Setup person 20 Setup person 20 Setup persorn 30 Operator 24 Setup person...
2. Consider the following batch flow process consisting of three process steps performed by three machines: Step 1 Step 3 Step 2 Processing time 1 minute/part Processing time 1.5 minute/part Processing time 2 minute/part Setup time No Setup No Setup 20 minutes Work is processed in batch at each step. Before a batch is processed at step 1, the machine has to be set up. During There are no inventory buffers between steps. a setup, the machine is unable to...
Gordon Company produces custom-made machine parts. A setup activity is required for the batches of parts that it produces. Activity output is measured using setup hours. The value-added standard (SQ) for this activity is zero. On July 1, at the beginning of the fiscal year, 15 setup hours were allowed and used per batch. The standard wage rate for setup labor is $24 per setup hour. During the first quarter of the new fiscal year, the company is planning to...
PA 84 In the welding operations of a bicycle manufacturer... In the welding operations of a bicycle manufacturer, a bike frame has a flow time of about 14.35 hours. The time in the welding operation is spent as follows: 3 hours waiting in front of the cutting machine for the batch to start, 2 hours waiting for the setup of the machine, 1 hour waiting that the other pieces of the batch go through cutting, 2 minute at the cutting...
5. Changeover of fixtures on a machine takes 35 minutes. Following the changeover, an aver- ed before the correct setting is achieved. For ch part the processing time is two minutes and the material cost is $1.50. The labor cost for a skilled setup person to do the changeover and adjustment is $15.50 per hour. The labor cost of the machine operator is $10.50 per hour. Currently, the part is produced in batches of 50 units. Suppose the setup procedure...
a) Setup Cost:
b) Setup Time:
Rick Wing has a repetitive manufacturing plant producing automobile steering wheels. Use the following data to prepare for a reduced lot size. The firm uses a work year of 305 days. Setup labor cost $40.00 per hour Annual holding cost $16 per unit Daily production (8 hours) 800 units day Annual demand for steering wheels 36,600 (305 days x daily demand of 120 units) Desired lot size (2 hours of production) 0 - 200...
A process has two stages. In the first stage, a machine makes two components, call them type A and B. It takes 250 seconds to switch production between the component types. During that time no production occurs. When in production, each component (A or B) requires 0.6 seconds to be completed. In the second stage, the components, A and B, are assembled to make a final product, call it C. The assembly stage can combine the two components into 1...
Most questions answered within 3 hours.
-
Write a program to solve the Josephus problem, with the following
modification:
Sample Input:
./a.out n...
asked 1 hour ago -
At the start of a CD it is spinning at a rate of 525 rpm
(revolutions...
asked 2 hours ago -
4. Without doing any calculations, predict whether the observed
∆T would increase, decrease or remain the...
asked 3 hours ago -
Based on the range, which of the following sets of scores has
the greatest variability? 3,...
asked 4 hours ago -
Ripples in a pond travel at a velocity of 3 m/s with one peak
passing a...
asked 4 hours ago -
A man stands on the roof of a building of height 13.0 mm and
throws a...
asked 4 hours ago -
The extent to which assets are financed by borrowed funds and
other liabilities is indicated by:...
asked 5 hours ago -
Explain in detail
Germany is the fifth largest economy
explain what goods and services Germany specializes...
asked 5 hours ago -
The density of platinum is 21.45 g/mL. If a cube of platinum
with a mass of...
asked 5 hours ago -
Accounts Receivable
Sales
A/R Posting
Extended Sales Invoice
Packing Slip
Compare invoice to packing slip 2...
asked 6 hours ago -
Michaella, age 23, is a full-time law student and is claimed by
her parents as a...
asked 6 hours ago -
Why are polymers not typically casted into products?
asked 6 hours ago