For the block diagram below, find the following if Vsecondary = 36Vrms, 60 Hz, and Rload = 150 ohms. Round off to the tenths place.
i. Peak Voltage out of the Diode Bridge:
ii. DC Voltage out of the Diode Bridge with no filter
capacitor:
iii. DC Load Current
For the block diagram below, find the following if Vsecondary = 36Vrms, 60 Hz, and Rload...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform from the wall power and convert it to a “regulated” dc value giving 15 volts +, - 1.0 volts across a 1200-ohm output load resistor with no more than 2% ripple voltage, all at a total component parts cost of less than $175.00 (US$). Your design process/ analysis is to be conducted by hand. Consider for this design task: Assume an ideal transformer and...
TCO 2) For the circuit below, if Vcc is 28 volts and Rb is 4.7k ohms, find the base and collector voltages and currents for an input of OV and 5V. Beta 300, the motor resistance is 400 ohms. AG1 NI MOTOR SERVO Vin N Yout Rb 1a: When Vin OV, find: lb = Ic = Vbase Vcol 1b: when Vin 5V, find: IC Vbase HTML Editor Question 6 7 pts TCO 1) Find the following for an input of...
1) A classical rectifier uses a standard 120 V/25.2 V 60 Hz transformer. What ideal output DC voltage will result if a single-phase full-wave diode bridge is used with a large capacitor and the input is exactly 120 Vrms? Assume each diode's forward voltage drop is 1 V. Design a capacitor if the load is 50 W and the voltage ripple is 1 V peak-peak?
1. AC generators used in submarines quite often have a frequency of 1,000 Hz and an output voltage of 24 volts (r m s ). If this generator is connected to a diode bridge rectifier: (a) Hat I sthe output DC average voltage without a filter capacitor? (b) With capacitors of 10,000 micro farads, but no load, what is the output Vdc capacitor as a filter as, but no load, what is the output VDC? (c) When a resistive load...
Find the following for an input of 120 VAC(RMS), 60 hertz, given a 20:1 stepdown transformer. The secondary is less voltage than the primary. Rload is 100 ohms. Round off to the nearest tenths place. 1a: Primary or input peak voltage = 1b: Secondary peak voltage = 1c: Primary peak current =
part g Q4. Most electronic systems need a dc voltage to work properly. The AC-to-DC power supply system is including a transformer, a rectifier and a capacitor input filter. The AC input voltage is 110 Vrms at 60 Hz. (a) Draw the full wave bridge rectifier circuit with transformer which steps down voltage to safer and lower levels that are more suitable for use with diodes (b) Show how the capacitor input filter connects to the rectifier output in the...
please help Question 1 Consider the following circuit, where the reverse saturation current (Is) is the same for each diode. D2 o Vo Di Vi WWW R 32 23 a. b. Determine an algebraic expression for V1, for a given Vo, and Is. Given an Is of 40 FA and R1 = 3.3 kl , determine the Vi that produces an output voltage (V.) of 0.625 V. C. Recalculate question-b if Is were to be a thousand times greater at...
O Modules S Agile Product Life y erse... ROADP $ Nevlersey local N. G Google a Northersey Nev. Pages. Welcome. me t Question 3 6 pts (TCO 1) Find the following for an input of 120 VAC(RMS), 60 hertz, given a 15:1 stepdown transformer and a full-wave bridge rectifier. Rload is 82 ohms. Round off to the nearest tenth place. 1a: Primary or input peak voltage - 1b: Secondary peak voltage - 1c: Peak voltage out of the rectifien id:...
Q1)A half-wave rectifier has a 120 Vrms 60 HZ ac source. The load IS 50 W. Determine the value of a filter capacitor to keep the peak-to-peak nipple across the load to less than 1.5V. Seled the one best answer from the choices given below(a) 410 UF (d) 3270 uF (b) 820 UF (e) 6540 UFQ2)A diode whose internal resistance is 200 is to supply power to a 1000 load from 110V (rms) source pf supply. Calculate(a) peak load current...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform and convert it to a “regulated “dc value giving 12 volts +, - 1 volt across a 2000-ohm output load resistor with no more than 2% ripple voltage. You may assume: a. An ideal power transformer as discussed in class. b. For hand computations, you must assume a diode given by Figure 4.8 page 185. c. A filter capacitor sized per the textbook equation...