Homework Answers
Add Answer to:
I want right answer
Problem Design and draw a first-order op amp-RC high-pass filter with 3-dB...
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a low-pass first order filter is used, determine the attenuation (Attenuation %, and Attenuation(dB)) of the f...
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a low-pass first order filter is used, determine the attenuation (Attenuation %, and Attenuation(dB)) of the filtered analog signal at 50, 75 and 200 Hz. (use k -1) o Determine the order of the filter if magnitude ratio of <0.01 is needed at 200 Hz.
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a...
Active Low-pass and High-pass Filters for Crossover Circuitry (PSPICE) Design a first order active high-pass filter...
Active Low-pass and High-pass Filters for Crossover Circuitry
(PSPICE)
Design a first order active high-pass filter with cut-off
frequency of 1 kHz & gain 20dB.
Design a first order active low-pass filter with cut-off
frequency of 1 kHz & gain 20dB.
Plot the magnitude and phase responses of the active high-pass
and low-pass filters you have designed using PSpice (Use UA741 Op
amp and ±12V dual supply).
Connect your active low-pass and high-pass filters as shown in
Fig. 1-b. Assume...
13.6 Design a first-order active high-pass filter with a response of +12 dB in the high-frequency...
13.6 Design a first-order active high-pass filter with a response of +12 dB in the high-frequency limit and -20 dB at 1.2 kHz. Let C 1 nF
13.6 Design a first-order active high-pass filter with a response of +12 dB in the high-frequency limit and -20 dB at 1.2 kHz. Let C 1 nF
Design a first order high-pass Butterworth filter that achieves the following specifications: Cutoff frequency = 770...
Design a first order high-pass Butterworth filter that achieves the following specifications: Cutoff frequency = 770 Hz Stop-band corner frequency = 132 Hz dB slope = 20dB / decade Gain at 132 Hz ≈ -14.9 dB Show working for all determined values of R and C
C, V. Low-pass High-pass Procedure: Design the following filters and be certain to provide the co...
C, V. Low-pass High-pass Procedure: Design the following filters and be certain to provide the component values you used in a table like those shown on the third page. Record your calculations because they will be requested in the lab report. To make the lab simpler let the input resistor Ri be the same for all stages. In this particular case the loading effects from cascading the op-amp circuits will have little influence on the overall gain. Refer to your...
Construct an active (with op Amp) high pass RL filter circuit with the following requirements: •...
Construct an active (with op Amp) high pass RL filter circuit with the following requirements: • L = 100mH • Cutoff frequency = 5500 Hz • Gain = 5V/V • Conduct an AC Sweep & indicate the cutoff frequency on the graph using cursors
2.Design a high pass filter with a -3 dB frequency of 1 MHz, using the same...
2.Design a high pass filter with a -3 dB frequency of 1 MHz, using the same parts in problem #1. Sketch the magnitude and phase of the transfer function. Answer Qs 2 only I put 1 for the reference 1.Design a low pass filter with a – 3 dB frequency is 1 MHz. The largest capacitor that I have in my bin is 10 nF. a. Find the transfer function for the circuit and sketch its magnitude and phase that...
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2 3.a. Use a 2.2nF capacitor to design a high-pas...
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2 3.a. Use a 2.2nF capacitor to design a high-pass filter to have a cutoff frequency of Skn Draw a schematic of your design. Show all component values and voltages c. Sketch the frequency response of the voltage gain and phase shift Magnitude dB Frequency Hz Phase Frequency Hz
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2...
CIRCUIT ANALYSIS 2. Design a second order high pass filter with a passband gain of 20...
CIRCUIT ANALYSIS
2. Design a second order high pass filter with a passband gain of 20 dB, and a 3 dB upper cutoff frequency ofS Hz.[D] (40)
1) Design a low-pass RC device with the following specifications: a) Input x(t) and output y(t)...
1) Design a low-pass RC device with the following specifications: a) Input x(t) and output y(t) b) Bandwidth which is defined as the range of frequencies (from 0 Hz to ??, the − 3dB point ) allowed to pass through without significant attenuation = 100Hz c) Static gain = 14dB d) The system has −20 dB/decade rolloff at high frequencies (thus first-order LP filter) Assume that you have one and only one resistor value available to you, and that resistance is...
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a low-pass first order filter is used, determine the attenuation (Attenuation %, and Attenuation(dB)) of the filtered analog signal at 50, 75 and 200 Hz. (use k -1) o Determine the order of the filter if magnitude ratio of <0.01 is needed at 200 Hz.
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a...
Active Low-pass and High-pass Filters for Crossover Circuitry
(PSPICE)
Design a first order active high-pass filter with cut-off
frequency of 1 kHz & gain 20dB.
Design a first order active low-pass filter with cut-off
frequency of 1 kHz & gain 20dB.
Plot the magnitude and phase responses of the active high-pass
and low-pass filters you have designed using PSpice (Use UA741 Op
amp and ±12V dual supply).
Connect your active low-pass and high-pass filters as shown in
Fig. 1-b. Assume...
13.6 Design a first-order active high-pass filter with a response of +12 dB in the high-frequency limit and -20 dB at 1.2 kHz. Let C 1 nF
13.6 Design a first-order active high-pass filter with a response of +12 dB in the high-frequency limit and -20 dB at 1.2 kHz. Let C 1 nF
C, V. Low-pass High-pass Procedure: Design the following filters and be certain to provide the component values you used in a table like those shown on the third page. Record your calculations because they will be requested in the lab report. To make the lab simpler let the input resistor Ri be the same for all stages. In this particular case the loading effects from cascading the op-amp circuits will have little influence on the overall gain. Refer to your...
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2 3.a. Use a 2.2nF capacitor to design a high-pass filter to have a cutoff frequency of Skn Draw a schematic of your design. Show all component values and voltages c. Sketch the frequency response of the voltage gain and phase shift Magnitude dB Frequency Hz Phase Frequency Hz
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2...
CIRCUIT ANALYSIS
2. Design a second order high pass filter with a passband gain of 20 dB, and a 3 dB upper cutoff frequency ofS Hz.[D] (40)
Most questions answered within 3 hours.
-
Why does Max Weber distinguish between "power," "authority," and
different types of authority? What is he...
asked 1 minute ago -
In recent years, 80% of those accused of Driving Under the
Influence (DUI) get convicted (includes...
asked 1 minute ago -
What would the solow growth model look like if there was a
production function which had...
asked 6 minutes ago -
A company project has an initial cost of $40,000, expected net
cash flows of $9,000 per...
asked 8 minutes ago -
How do you use strategy in your current position or how does
your current position align...
asked 10 minutes ago -
a person's ability to be properly diagnosed with a
disease/condition can be affected by the person;s...
asked 9 minutes ago -
John needs 40 Eternal Light flashlights. Each Eternal Light
flashlight requires 3 bulbs, and each bulb...
asked 17 minutes ago -
1) If Nominal GDP is $16,000 billion and the GDP deflator is 50,
then Real GDP...
asked 23 minutes ago -
D. A student completed 20 courses in the School of Arts and
Sciences. Her grades in...
asked 2 hours ago -
teo
pucks moving on a frictionless air table are about to collide. the
1.5 kg puck...
asked 2 hours ago -
Problem #1
The area between Z = 0 and Z = 2.50
The area between Z...
asked 3 hours ago -
1. What is the meaning of the term communication style?
2. What are the benefits to...
asked 3 hours ago