Write a behavioral code in Verilog to implement a RAM of 256 words with each word having 8 bits. RAM must have Enable, Read/Write pins and will have address bus, data bus (for both input and output). Write a testbench and demonstrate the working of all its read/write operations.
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Write a behavioral code in Verilog to implement a RAM of 256 words with each word...
Write a behavioral Verilog module for a 4-bit Johnson counter that has 8 states. The counter loads the "0000" state if reset is low. The counter should start and end with this state. Write a testbench to verify the correctness of the 4-bit Johnson counter. The testbenclh should have a clock with a period of 20ns and a reset signal. The testbench should store the 4-bit binary outputs of the counter in a file, which will be used to provide...
please explain Question 3 1. Write behavioral Verilog code to calculate the factorial of a 3-bit unsigned number. (10 points) 2. Implement the following function using two 3-input-output lookup tables: f = a'be + acid. (10 points)
Question 3 [maximum 6 marks] Using the basic SRAM cell developed in Question 2, implement a 4x4 RAM as given below. Write a testbench to simulate and test its working. Input data Word BC WordI 2×4 Word 2 nc Word 申 Read Write Output dala
Consider 512Kx8bits dynamic RAM chips where the memory access time is 2/3 of the memory cycle time. These chips have an Address Bus, a bi-directional Data Bus, a Read/Write control line and a Chip Select line. (a) Draw the diagram of a memory organization that will contain 4 megabytes, will have a 32-bit bi-directional data bus and will yield one word (32-bits) every access time if words are read from consecutive memory locations (in bursts). Clearly show and explain the...
Please implement the function z(a, b, c) in Verilog HDL. Note: Please write your code in one module. ? = ? × ? + ?, where ? = ?^3 − ? ? = ???? ( 8/?×? , ?) Hint: output wire z; input wire a, b, c
i just want the code Write a module in Verilog HDL that describes a parallel load shift register. The following are the requirements for the shift register • The shift register shifts right by one position at a time The shift register size (in bits) is set by a parameter called WIDTH The shift register has a parallel data bus input for loading a value in parallel. The parallel bus is called datalp. The size of the dataly, bus uses...
write a program in C Write a program to implement the following requirement: The program will read from standard input any text up to 10, 900, characters and store each unique word (any string that does not contain any whitespace) into a node of a linked list, following the following Node struct: struct NODE { char *word; struct NODE * prev; Note that each node must store a unique word, i.e., no word is stored in more than one node....
FIRST ACTIVITY: (100/100) . SIMPLE 4-BIT ARITHMETIC LOGIC UNIT (ALU): This circuit selects between arithmetic (absolute value, addition) and logical (XOR, AND) operations. Only one result (hexadecimal value) can be shown on the 7-segment display This is selected by the input sel (1..0) B A-BI A+B A xnor B A nand B Input EN: If EN-1result appears on the 7 segment display. If EN=0 → all LEDs in the 7 segment display are off Arithmetic operations: The 4-bit inputs A...
Objective: Creating a register file (memory) using Verilog. The register file is made up of four registers and each register holds one nibble (half a byte, i.e., four bits) 3. Create a D flip-flop AD flip-flop holds 1 bit of data, and it only changes its data when the clock changes. We want a positive edge triggered flip-flop. Design your Verilog D flip-flop, so we will create them now. Enter the 2 to 4 line decoder. We will need two...
Write an Verilog code for a 8-bit subtractor (Bits are in 1's complement) using the following: 1. 5-bit parallel adder 2. 3-bit parallel adder The condition are as follows: 1. The Most Significant bits of the subtractor must be given to the 5-bit parallel adder. 2, The Least Significant bits of the subtractor must be given to the 3-bit parallel adder. 3. The input A will be assign to the switches with the least significant bit A[0] linked to SW0....