Please implement the function z(a, b, c) in Verilog HDL. Note: Please write your code in one module.
? = ? × ? + ?,
where
? = ?^3 − ?
? = ???? ( 8/?×? , ?)
Hint: output wire z;
input wire a, b, c
module function_z (a, b, c, z);
input a, b, c;
output z;
wire u, v;
assign u = (a * a * a) - b;
assign v = (8 / (a * b)) ~^ c;
assign z = u * v + c;
endmodule
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Please implement the function z(a, b, c) in Verilog HDL. Note: Please write your code in...
PLEASE WRITE CODE IN VERILOG ONLY NO OTHER HDL LANGUAGE. C3. a) Write a HDL code for a seven-segment display unit using your preferred HDL program. b) Write a TestBench to verify all functionalities of the designed seven-segment display. Note: You must specify the name of the HDL programming language that you are using.
(a) Write "continuous assign statement" in Verilog HDL for the output Z described by the below bread board setup. [Note that all the gates are NOR gates.) (8 points) V VCC GND GND O O VCC O (b) Write Verilog HDL for circuit in (a) using if-else statements within an always block. (6 points) (c) Write Verilog HDL for circuit in (a) using case statements within an always block. (6 points)
Please code the following in Verilog: Write the HDL gate-level hierarchical description of a four-bit adder-subtractor for unsigned binary numbers similar to the following circuit. You can instantiate the four-bit full adder described in the following example code Figure 4.13a, 4-Bit adder-subtractor without overflow Inputs: 4-Bit A, 4-Bit B, and Mode M (0-add/1-subtract) Interfaces: Carry Bits C1, C2, C3 Outputs: Carry C (1 Bit, C4), Sum S (4 bit) Bo A FA FA FA FA module Add half (input a,...
Using Verilog, write a simulation code that shows the function g(w, x, y, z) = wxyz + w’x’y’z+w’x’yz’+w’xy’z’+wx’y’z’ using a 4 to 16 decoder that is built with two 3 to 8 decoders. The 3 to 8 source code I'm using is: module Dec3to8( input[2:0] A, input E, output[7:0] D ); assign D[0] = E & ~A[2] & ~A[1] & ~A[0]; assign D[1] = E & ~A[2] & ~A[1] & A[0]; assign D[2]...
1- Please answer all the question 2- with clear handwriting Thank you, 3. Design a combinational circuit with inputs a, b, c, d and outputs w, z, y, z, where the input and output both represent a signed numbers (2s complement). The output is 7 less than the input, if the input is positive, or zero. If the input is negative, the output is 3 greater than the input. 7. Use the Boolean functions developed in problem #3 to create...
Verilog , ignore the 'P5_ALU' part. just write the verilog implementation. 5. [Verilog] Implement the sequential logic module 'P5_ALU' with state diagram using input variable cont. The 'P5_ALU' module produces ALU output 'result' based on the state shown in Table 1 Input data X[15:0], YI15:0], cont Output data: result[15:0] Reset Result State X*Y X+1 0 D Max(X,Y) Table 1. Output 'Result' of 'P5_ALU Figure 3. State diagram of 'P5_ALU 5. [Verilog] Implement the sequential logic module 'P5_ALU' with state diagram...
Building and testing basic combinational circuits using Verilog HDL Description: Build and test the following circuits using gate-level modeling in Verilog HDL. 1. 3-input majority function. 2. Conditional inverter (see the table below: x - control input, y - data input). Do NOT use XOR gates for the implementation. x y Output 0 y 1 y' 3. Two-input multiplexer (see the table below: x,y - data inputs, z - control input). z Output 0 x 1 y 4. 1-bit half...
Building and testing basic combinational circuits using Verilog HDL Description: Build and test the following circuits using gate-level modeling in Verilog HDL 1.3-input majority function 2.Conditional inverter (see the table below: x - control input, y -data input). Do NOT use XOR gates for the implementation. Output 3. Two-input multiplexer (see the table below: x.y -data inputs, z- control input) Output 4. 1-bit half adder. 5. 1-bit full adder by cascading two half adders 6.1-bit full adder directly (as in...
please explain Question 3 1. Write behavioral Verilog code to calculate the factorial of a 3-bit unsigned number. (10 points) 2. Implement the following function using two 3-input-output lookup tables: f = a'be + acid. (10 points)
Write a behavioral code in Verilog to implement a RAM of 256 words with each word having 8 bits. RAM must have Enable, Read/Write pins and will have address bus, data bus (for both input and output). Write a testbench and demonstrate the working of all its read/write operations.