Saturated liquid water flows through a pipe and is heated by a pump that vaporizes the water. The pipe has water flowing at a rate of 50 grams per second and at a pressure of 180 kPa. The pump receives heat from a reservoir at 10°C and supposedly requires 32 kW of power.
a. Find the heat from pump required to vaporize the water in the pipe
b. Find the temperature of the water inside the pipe.
c. Find the Coefficient Of Performance of the heat pump
d. Verify that the 32KW is enough to power the pump.
Saturated liquid water flows through a pipe and is heated by a pump that vaporizes the...
(a) An insulated piston cylinder device contains 5 L of saturated liquid water at a constant pressure of 150 kPa. The cylinder was equipped with the electric heater inside it. The liquid is heated at constant pressure until it becomes saturated vapour. Determine the entropy change of the water during this process in kJ/K. (10 Marks) (b) A stream of refrigerant R134a enters a steady flow device at 100 kPa, 50 °C at a rate of 1 kg/s. Two streams...
0.1 kg/s of saturated liquid water enters an adiabatic reversible pump at 10 kPa and exits at 4 MPa. Calculate the input power required by the pump. Select one: O a. 4 kW O b. -4 kJ/kg O c.4kJ
1 pts Cold water at 10°C flowing a rate of 2 kg/s is heated to 35°C inside a heat exchanger by saturated steam. The steam enters the heat exchanger as saturated vapor at 100 kPa and leaves as saturated liquid at the same pressure. The heat exchanger losses heat at a rate of 20 KW. The mass flow rate of the steam is most nearly: 0.185 0.101 0.748 0.548 0.312 0.243 0.443 0.085
Liquid water at 95°C and at l atm flows through a heated pipe at a flow rate of 3.2 kg/s. It then leaves the pipe as steam. The water receives 10333440 J of heating from the pipe. Calculate the temperature of the steam leaving the pipe. Take 0°C as the reference with zero enthalpy. The boiling point at the pressure of the system is 100°C. Thermal properties: Cp of liquid water: 4200 J/kg.K Cp of steam: 1800 J/kg.K Enthalpy of...
Refrigerant 134a flows through an ideal vapor compression heat pump system with a heating capacity of 60,000 Btu/hr. The condenser operates at 200 psi, and the evaporator temperature is 0°F. The refrigerant is a saturated vapor at the evaporator exit and a saturated liquid at the condenser exit. The temperature at the compressor exit is 180°F. Assuming the compressor is not 100% isentropic, determine: a) Mass flow rate (lbm/min) b) Compressor power (hp) c) Isentropic compressor efficiency d) Coefficient of...
An ideal vapor-compression heat pump cycle using R-134a is used to heat a house. The inside temperature is 22 ℃; the outside temperature is 0 ℃ Saturated vapor at 2.2 bar enters the compressor, and saturated liquid leaves the condenser at 3 ba. The mass ow rate is 0.2 kg/s. Detemine: a the power iput to the compressor (in kw) b. the coefficient of performance c. the coefficient of performance if the system were used as a refrigeration cycle d....
4. Water is the working fluid in a Carnot vapor power cycle. Saturated liquid enters the boiler at 16 MPa, and saturated vapor enters the turbine. The condenser pressure is 8 kPa. The mass flow rate of steam entering the turbine is 120 kg/s. Determine (a) the thermal efficiency. (b) the back work ratio. (c) the net power developed, in kW. (d) the rate of heat transfer from the working fluid passing through the condenser, in kW.
6 Water is heated in a pipe by exchanging heat with a warmer fluid that flows outside the pipe. Inside diameter of the pipe is dn 0.045 m and outside diameter dour0.05 m. Mean velocity of the water in the pipe is um-0.31 m/s and the bulk temperature is 323 K (density 988 kg m-3; viscosity 0.00055 kg m' sı. Pr 3.56, thermal conductivity k 0.64 W m1 Kt). The material of the pipe has thermal conductivity k 0.61 W...
please solve all of them awestion 3 (35 pts) water at Tjz1SC is heated in a chamber by mixing it with steam at paa300 kPaond TR320С The saturated liquid water and the steam enter the mibxing chamber through separate and independent inlet pipes. The saturated liquid water enters the mixing chamber at a rate of 3.0 kg/s, and the chamber loses heat to the surrounding air at 30 Cat a rate of 12 kW. The mixture leaves the mixing chamber...
Ten kilograms of water in a piston/cylinder arrangement exists as saturated liquid/vapor at 100 kPa, with a quality 20%. The system is now heated so that the volume triples. The mass of the piston is such that a cylinder of 300 kPa will float it. (a) Find the final temperature. (b) Find the heat transfer in the process. (c) What is the phase of water when the piston just starts to lift up? (d) Sketch the process on a P-v...