Draw the schematic of a 2-4 line decoder using basic gates. (xou need to use 7404,...
answer as u can make it up Lab #7-8 Objectives: 1. To understand Multiplexers and De-multiplexers. 2. To implement a basic multiplexer using AND, OR, and NOT, gates. 3. To verify the operation of Integrated Mulitplexers. Equipment: Digital Multi-meter, Breadboard, Power Supply, Function Generator, Oscilloscope. Components: 7404, 7408, 7432, 74151, 74138, LEDs, Resistors Procedure: 7. Draw the schematic of a 2-1 De-multiplexer using basic gates. 8. Write down the IC numbers and pin numbers of the gates in your schematic....
from 6 to 1 and from 4 to 1 Draw the schematic diagram for the circuit shown in Figure W1.1 using schematic capture software (refer Table 2). The drawing should include labels for DC supply and 1/O pin numbers as in the actual ic pin configuration (Refer AN2). W1.2 Instruction You are required to design and built a 1-digit decimal down counter from decimal value A to decimal valuie Ron a breadboard (refer ANI). Values of A and B will...
Draw the logic diagram of a 2-to-4-line decoder using (a) NOR gates only and (b) NAND gates only. please show the steps
I need help with part 1 and part 2 if anyone can help me out. To draw the schematic we use logic.ly. Thank you for your help. Combinational Gates: Part A 1) 2 to 4 Decoder a. Draw a 2 input to 4 output decoder. Utilize class notes, ZYBooks, and other online resources to determine the proper schematic and functionality b. Create a truth table. c. Explain what the circuit is used for. d. Include 1 screen shot in your...
Design a Digital combinational logic circuit using logic gates that has 4 inputs and 2 outputs. The circuit: i. Turns on a Red LED if its input is a multiple of 2. (i.e., 0, 2, 4, 6, 8 …..) ii. Turns on a Green LED if its input is a multiple of 3. (i.e. 0, 3, 6, 9) - Draw the truth table for the circuit, bearing in mind that this circuit has 4 inputs and 2 outputs, meaning your...
Task (10 points): (1) Approach 1: Implement a 4-to-16-line decoder using the schematic capture feature of Xilinx ISE. On the schematic, add a text that clearly shows your name and eRaider ID. (2) Approach 2: Write and compile a 4-to-16-line decoder Verilog gate-level description. (3) Approach 3: Write and compile a 4-to-16-line decoder Verilog behavioral description. (4) Create an appropriate test file to do an exhaustive test. Exhaust all the possible input codes in 3 the following order: 0000 →...
Design a circuit to add two 2-bit binary numbers and display the results of the addition as a 3-bit binary number, with the most significant bit be the carry out. To do this, you will use the four switches on your Breadboard Companion as your two 2-bit number inputs. Three of your LEDs will be used to represent the 3-bit output of your circuit. Complete a truth table for the expected output values on the lab data sheet attached. Use...
Task 1: One implementation of a multiplexer uses a decoder. Using Logic Circuit,create a new schematic, import one of the decoders created in a previous lab and create a logic dircuit that implements the truth table below Task 2: Create a logic circuit that can display two 4-bit digits on two 7-segment displays using a single 7- segment display decoder and 4 multiplexers. To do this you will use four switches to enter the first number, and a second set...
need help please thanks! Draw a gate-level schematic for the fall-adder module. XOR gates can be used to usplement Sotput; two levels ofNAND ples are handy for tn lema îngC, as a sum of products Create a MOSFET cirout for each of the logic gates you used in step 1 Your lab assigment this week is to design and test a CMOS circuit that performs addition Some suggestions on how to proceed Let's start with a simple ripple-cany adder based...
AT&T 8:14 AM 100% < Back ECE204.Lab09-DataSheet.docx Гђ ECE 204 Lab 09 Basic Logic Gates Name: Name: Purpose: Replace this with a statement of purpose. Procedure A Digital input output test setup The digital circuits built throughout the rest of this lab will have the basic input and output setup as shown in Figure 1 Figure: Digital circuit input and output test setup The components for this setup include single throw dual pole switches and an LED. Figure 2 shows...